Bedienungsanleitung Parkside IAN 304520 PTBM 500 E5 (Seite 30 von 144) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Polnisch)

748958

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

GB IE

place the battery in direct sunlight and

do not use or store it in motor vehicles

in hot weather.

• Store used batteries in the original pa-

ckaging and keep them away from me-

tal objects. Do not mix (up) unpacked

batteries! Otherwise this may cause the

battery to short-circuit, resulting in da-



• Remove batteries from the device if this

is not going to be used for a prolonged

period, unless it is to be used in emer-

gencies!

• NEVER touch batteries which have

leaked without appropriate protection.

If the leaked liquid comes into contact

with the skin, you should rinse off this

area of the skin immediately under run-

ning water. Make sure at all events that

your eyes and mouth do not come into

contact with the liquid. If they do, seek

medical advice immediately.

• Clean the battery contacts and the

equivalent contacts in the device before

inserting the batteries.

Assembly

The bench drill is supplied disassembled.

Clean the column tube (14), baseplate (17),

drilling bench (20), vice (23) and the drill

chuck (4) beforehand, with a dry cloth.

1. Place the column tube (14) on the ba-

seplate (17). Bolt the column tube (14)

to the baseplate (17) with the three as-

sembly srews (16) supplied. Tighten the

assembly srews (16) moderately tight

so that the threads in the baseplate (17)

do not strip.

2. Place the drilling bench (20) on the co-

lumn tube (14). Push the drilling bench

(20) into a lower position. Use the



bench (20) in a lower position.

3. Place the vice (23) on the drilling



the drilling bench (20) by means

of the enclosed assembly screws

(22) together with the washer

and the lock washer in the order

as shown.

4. Place the motor unit (13) on

the column tube (14). Secure

the motor unit (13) with the two

clamping screws (27) on the

side using the enclosed Allen key

(25).

5. Bolt the three drill lifting arms

into the spindle guide (9). Tigh-

ten the three hole lifting arms

with a spanner (AF 6 mm).

6. Release the clamping screw from

the depth stop (8).

7. Mount the laser on the motor unit



Make sure that the battery com-

partment (36) is on the side of

the hand spindle guide (9).

8. Put the safety device (6) on the

upper part of the drill spindle

(7).

9. Secure the safety device (6) with

the clamping screw (28).

10. Fold the safety device (6) up-

wards. Insert the chuck (4) on

the taper of the drill spindle (7).

Push the drill chuck onto the drill

chuck tip with a few light taps.

Use a plastic hammer for this

purpose.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 304520 PTBM 500 E5 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info