Bedienungsanleitung Parkside IAN 310850 PISG 120 A1 (Seite 32 von 76) (Deutsch, Englisch, Holländisch, Französisch)

749299

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

32 GB/IE

zStart up

Note: The welding tool is suitable for weld-

ing with electrodes.

Use electrode retaining clips without pro-

truding retaining screws meeting today‘s

safety standards.

Be sure the ON / OFF switch

is set to

position “O“ (“OFF“) or the main supply

cable

is not plugged into the mains

socket.

Connect the welding cables according

to polarity and electrode manufacturer

instructions.

To do so, connect the port of the earth

terminal

(black) with the appropriate

outlet on the inverter welding machine

(black, marked with “-”).

Connect the port of the electrode holder

(red) with the appropriate outlet on

the inverter welding device (red, marked

with “+”),

Put on suitable protective clothing

according to provisions and prepare the

work area.

Connect the earth terminal

to the

workpiece.

Secure the electrode in the electrode

holder

Switch on the device by setting the ON /

OFF switch

to the “I“ (“ON“) position.

Set the welding current with the control

knob

according to the electrode used.

Note: Please see the table below for the

welding current according to electrode

diameter.

Ø Electrode welding current

1.6 40 – 55 A

2.0 55 – 65 A

2.5 65 – 80 A

3.2 80 – 120 A

Note: For the welding currents of 80 A to

120 A, please use welding electrodes with

a diameter of 3.2 mm (not included in the

scope of delivery).

Attention: Do not bring the earth

terminal

and the electrode holder

electrodes into direct contact with one

another.

Attention: When welding with elec-

trodes (MMA - manual metal arc

welding) the electrode holder

and the

earth terminal

lug must be connected

to positive (+) or negative (-) according

to the welding rod specifications.

Hold the welding shield

in front of

your face and begin welding.

To stop working, set the ON / OFF

switch

to the “O“ (“OFF“) position.

ATTENTION!

When the thermal overload protection is

triggered, the yellow control lamp

lights

up. In this case, no further welding is

possible. The device is still in operation for

the fan to cool the device. As soon as the

device is ready for use again, the yellow

control lamp

switches off automatically.

The welding function is now given again.

ATTENTION!

Be careful not to rub the welding rod against

the workpiece. This could damage the

workpiece and make it difficult to strike an

arc. Maintain the proper distance to the

workpiece after striking the arc. The distance

should correlate to the diameter of the

welding rod used. Maintain this distance as

accurately and consistently as possible whilst

welding. The angle between the welding

rod and the working direction should be

between 20 and 30 °.

Start up

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 310850 PISG 120 A1 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info