Bedienungsanleitung Parkside IAN 310860 PFBS 160 B2 (Seite 29 von 130) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

749296

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

PFBS 160 B2

■ 26 │ GB│IE

Supplementary safety instructions

for grinding and abrasive cutting

Special safety instructions for grinding and

abrasive cutting:

a) Use only the grinding accessories approved

for your power tool and only for the recom-

mended applications. Example: Never grind

with the side surface of a cutting disc. Cutting

discs are designed to remove material with

the edge of the disc. Any lateral application

of force on these grinding tools can lead to a

breakage.

b) Use only undamaged mandrels of the correct

size and length and without undercut on the

shoulder for conical and straight pencil grind-

ers. Using an appropriate mandrel reduces the

risk of breakages.

c) Avoid cutting disc jams or excessive contact

pressure. Do not make any excessively deep

cuts. Overloading the cutting disc increases the

stress and likelihood of tilting or blocking and

thus the possibility of a setback or a breakage

of the grinding tool.

d) Avoid putting your hand in the area in front

of or behind the rotating cutting disc. When

you move the cutting disc away from your hand,

it is possible, in the event of a kickback, that the

power tool along with the rotating disc could be

thrown out directly towards you along with the

rotating disc.

e) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steady until the

disc has completely stopped turning. Never

attempt to pull a rotating cutting disc out of a

cut. This could lead to a kickback. Identify and

remove the cause of the jam.

f) Do not switch the power tool back on for

as long as it is in the workpiece. Allow the

cutting disc to reach its full speed before you

carefully continue the cut. Otherwise, the disc

may jam, jump out of the workpiece or cause

kickback.

g) Support panels or large workpieces to

reduce the risk of the cutting disc jamming

and causing a kickback. Large workpieces can

bend under their own weight. The workpiece

must be supported on both sides, namely in the

vicinity of the cut, and also at the edge.

h) Be particularly careful when making plunge

cuts into existing walls or other obscured ar-

eas. The inserted cutting disc may cut into gas

or water pipes, electrical wiring or other objects

that can cause kickback.

Supplementary safety instructions

for working with wire brushes

Special safety instructions for working with

wire brushes:

a) Be aware that the wire brush loses wire

bristles even during normal operation. Do not

overstress the wires by applying excessive

pressure to the brush. The wire bristles can

easily penetrate light clothing and/or skin.

b) Allow the brush to run at working speed for

at least one minute before applying it to the

workpiece. Ensure that no one is standing in

front of or in line with the brush during this

time. Loose pieces of wire could ﬂy oﬀ during

the run-in period.

c) Aim the rotating steel brush away from your-

self. When working with these brushes, small

particles and minute pieces of wire can ﬂy oﬀ

at great speed and pierce skin.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 310860 PFBS 160 B2 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info