Bedienungsanleitung Parkside IAN 310860 PFBS 160 B2 (Seite 28 von 130) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

749296

Zoom out

Zoom in

Vorherige Seite

1/130

Nächste Seite

PFBS 160 B2 GB│IE │ 25 ■

q) Clean the ventilation slits of your power tool

regularly. The engine fan draws dust into the

housing and a strong accumulation of metal

dust can cause electrical hazards.

r) Do not use the power tool near ﬂammable

materials. Sparks can ignite such materials.

s) Do not use any attachment parts that require

liquid coolant. The use of water or other liquid

coolants may lead to an electric shock.

Additional safety instructions for all

applications

Kickback and corresponding safety instruc-

tions

Kickback is a sudden reaction caused when a ro-

tating attachment part, e.g. grinding disc, abrasive

band, wire brush, etc. catches or jams. Catching

or jamming leads to an abrupt stop of the rotating

attachment part. If this happens, an uncontrolled

power tool will turn rapidly against the direction of

rotation of the attachment part.

If, for example, a grinding disc catches or jams,

the edge of the grinding disc that is projecting into

the workpiece can get caught and break oﬀ the

grinding disc or cause a kickback. The grinding

disc can then ﬂy in the direction of the operator or

away from him, depending on the direction of rota-

tion of the disc at the blockage. This can also break

grinding discs.

A kickback is caused by improper or incorrect use

of the power tool. This can be avoided by taking

proper precautions as given below.

a) Hold the power tool ﬁrmly in both hands and

position your body and arms, so that they

can absorb the kickback forces. By taking

adequate precautions, the operator can stay in

control of the kickback forces.

b) Take special care when working around

corners, sharp edges, etc. Avoid allowing

the attachment part to bounce back from the

workpiece or jam in the workpiece. The rotat-

ing accessory tool is more likely to jam in cor-

ners or sharp edges or if it rebounds oﬀ them.

This can cause a loss of control or kickback.

e) Do not use toothed saw blades. Such acces-

sories often cause a kickback or loss of control

over the power tool.

d) Always move the attachment part in the

material in the same direction as the direction

in which the cutting edge leaves the material

(in other words, the same direction in which

the chips are thrown out). Guiding the power

tool in the wrong direction will cause the cutting

edge of the accessory tool to jump out of the

workpiece which can lead to the accessory tool

being pulled in this direction.

e) Always ﬁx the workpiece when using rotary

ﬁles, cutting discs, high-speed milling tools or

hard-metal tools. Even a minimal tilting in the

groove can cause these tools to jam and lead

to a kickback. When the cutting disc jams, it

usually breaks. When a rotary ﬁle, high-speed

milling tool or hard-metal milling tool jams, the

accessory tool can jump out of the groove and

lead to loss of control of the power tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 310860 PFBS 160 B2 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info