Bedienungsanleitung Parkside IAN 315808 PHS 9500 A1 (Seite 29 von 100) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

749330

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

25GB/IE

• Make sure that the ON/OFF switch (6), the throttle lock-out

switch (7) and the throttle trigger (9) function perfectly.

• This hedge trimmer is only allowed to be started after it is

completely assembled.

• Support the hedge trimmer when starting and hold it ﬁrmly.

Make sure that the cutting device can move freely.

10.1 Use (Fig. 1, 3, 4):

10.1.1 Starting when the engine is cold

Never allow the ranking rope (5) to whip back. This could

cause damage.

1. Remove the knives protection (F) from the cutting device

(1).

2. Place the hedge trimmer on a ﬁrm, level surface. The cut-

ting device (1) must not touch the ground.

3. Press the fuel pump “Primer“ (12) 6 times.

4. Switch the On/Oﬀ switch (6) to “I”.

5. Turn the choke (4) to „cold start“ .

6. Place the tip of your shoe into the rear handle (8)

7. Hold the hedge trimmer ﬁrmly by the front handle (3) and

pull the cranking rope (5) slowly until you feel resistance.

8. Now pull the cranking rope (5) quickly so that the engine

starts. If the engine does not start, repeat the process. As

long as the choke (4) is on „cold start“ , the engine

will only run for a short time and then switch oﬀ.

9. As soon as the engine is oﬀ, press the throttle lock-out

switch (7) and the throttle trigger (9) simultaneously. The

choke automatically jumps to the “warm start” operat-

ing position.“

10. Now pull the cranking rope (5) quickly again so that the

engine starts.

If the engine does not start after several attempts, read the

“15.Troubleshooting”.

Caution

Always pull the cranking rope (5) straight out. Hold the handle

of the cranking rope (5) ﬁrmly when the cranking rope (5) re-

tracts. Do not allow the cranking rope (5) to whip back.

Note:

At very high outdoor temperatures it is possible that even a cold

engine has to be started without using the choke!

Note:

If the cutting device (1) moves when it is idling or the engine

goes out when you release the throttle, you need to adjust the

carburettor (see section “12.2 Adjusting the idle speed”).

11. Lift the hedge trimmer.

12. Hold the front handle (3) ﬁrmly in your left hand.

13. Hold the rear handle (8) irmly in your right hand. The ball

of your hand now lies on the throttle lock-out switch (7)

and your index ﬁnger operates the throttle trigger (9).

14. After pulling the throttle trigger (9), once, the engine

should idle.

15. Run the engine to warm it up.

10.1.2 Starting with warm engine

1. Switch the On/Oﬀ switch (6) to „I“.

2. The Choke must be set to „warm start“ to start the

warm engine.

3. Place the tip of your shoe into the rear handle (8).

4. Hold the hedge trimmer by the front handle (3) and pull

the cranking rope (5) slowly until you feel resistance.

5. Now pull the cranking rope (5) quickly. The appliance

should start after 1–2 pulls. If the appliance still hasn’t

started after 6 pulls, repeat the process as described in

“10.1.1 Starting when the engine is cold”.

10.2 Stopping the engine

10.2.1 Emergency stop sequence

If you need to stop the appliance immediately, switch the On/

Oﬀ switch (6) to „0“.

10.2.2 Normal sequence

Release the throttle control (9). The engine idles. Then switch

the On/Oﬀ switch (6) to „0“.

10.3 Operation of the hedge trimmer:

1. Hold the hedge trimmer on its rear handle (8) and press

the throttle lock-out switch (7).

2. Hold the front handle (3) with your other hand.

3. Press the throttle trigger (9).

4. The cutting device will start moving.

If you release the throttle trigger, the cutting device will stop

and the engine will idle.

Contact the manufacturer if the cutting device still continues to

run in idle mode.

Do not continue working with the hedge trimmer in such a con-

dition.

10.4 Adjusting the rear handle (8).

To make working with the hedge trimmer easier it is possible

to choose one of the 3 working positions of the rear handle.

• When adjusting the throttle trigger (9) can not be pressed.

1. Use your left hand to hold the hedge trimmer on its front

handle (3).

2. Slide the locking handle (10) to the rear and turn the rear

handle to the desired position.

3. Release the locking handle (10). Make sure that the lock-

ing handle engages again and that the handle is secured.

10.5 Cutting blade (1) blockages

If the cutting blade (1) becomes blocked during operation,

switch oﬀ the hedge trimmer with the on/oﬀ switch (6) and

remove the spark plug connector (16).

Then remove the material that causing the blockage and check

the cutting blade (1) for possible damage.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 315808 PHS 9500 A1 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info