Bedienungsanleitung Parkside IAN 49374 PSB 1050 A1 (Seite 40 von 55) (Englisch, Portugiesisch, Spanisch)

744937

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

40 GB/MT

General safety advice for electrical power tools / Before first use

J If the inserted tool jams, switch off the

electrical power tool immediately. Be

prepared for high reaction torques as they may

cause kickback.

J Always keep the device clean, dry

and free of oil or grease.

When carrying out work during which

the insertion tool could hit hidden

power cables or the power cable of the

appliance itself, hold the appliance by

the insulated handling surfaces. Contact

with a live cable can also make metal appliance

parts alive and cause an electric shock.

J Keep your workplace clean and tidy.

Mixing materials is particularly dangerous.

Dust from light metals can burn or explode.

J Wait until the electrical tool has come

to a standstill before putting it down.

The insertion tool could get caught up in some-

thing and this may lead to control of the electrical

tool being lost.

Caution utility services!

DANGER! Ensure that you do not strike

electrical cables, gas or water pipes when

you are working with the electrical power

tool. Check a wall using a suitable detector before

you drill or cut slots.

Original accessories /

attachments

Use only the accessories and attachments

detailed in the operating instructions.

The use of inserted tools or accessories other than

those recommended in the operating instructions

could lead to you suﬀering an injury.

Before ﬁrst use

DANGER OF INJURY!

Switch the device oﬀ and pull the plug out of the

mains socket before carrying out any work on the

device.

Mounting or adjusting

the additional handle

NOTE: For reasons of safety, you may only use

this appliance with a properly mounted additional

handle

j Turn the wing screw

anti - clockwise and

mount the additional handle

in the vertical

position. The ratchet settings have be pushed

over the two green locking pins on the spindle

neck of the appliance.

j Tighten the wing screw

by turning it clock-

wise.

NOTE: Adjust the additional handle

into the

various ratchet settings according to the position

you are working in. To do so, loosen and close the

additional handle as described above.

Using the depth stop

j Loosen the wing screw

j Pull the depth stop

out as far as necessary

so that the distance between the tip of the drill

and the tip of the depth stop corresponds to

the desired drilling depth.

j Firmly tighten the wing screw

Inserting tools

Quick - action drill chuck / spindle lock:

j Your percussion drill has a fully automatic spin-

dle lock

and is ﬁtted with a single - sleeve

drill chuck with radial lock “Made in Germany”

j When the motor comes to a standstill, the drive

train will lock so that you can open the quick -

action drill chuck

by turning it .

j After you have inserted the tool you wish to

use, turn the drill chuck

until you cannot

hear any more clicks. The drill chuck will lock

automatically. The spindle lock releases itself

automatically when the motor is started (by op-

eration of ON / OFF switch

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 49374 PSB 1050 A1 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 49374 PSB 1050 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info