Bedienungsanleitung Parkside IAN 49374 PSB 1050 A1 (Seite 41 von 55) (Englisch, Portugiesisch, Spanisch)

744937

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

41 GB/MT

Assembly tools for screws and nuts:

j When using screwdriver bits, always use a

universal bit holder.

j To screw things in, always switch the changeover

switch “drill / percussion drill”

to the right to

position

Fitting / using the dust

extraction device

j Only use the dust extraction device when work-

ing on cement, brick and building stone. Wood

or plastic shavings could easily lead to the de-

vice becoming blocked.

ATTENTION! FIRE HAZARD! Do not work

on any metal materials when you have ﬁtted

the dust extraction device. Hot metal ﬁlings could

set parts of the dust extraction device on ﬁre.

NOTE: The dust extraction device

can only be

ﬁtted to the additional handle

if the depth stop

has previously been removed. If need be, loosen

the wing screw

by turning it anti - clockwise and

remove the depth stop

. Attach it again after

you have ﬁtted the dust extraction device

and

tighten the wing screw

again.

j Loosen the sing screw

and place the dust

extraction device

precisely onto the addi-

tional handle

j Tighten the wing screw

by turning it clock-

wise.

j You should preferably use a workshop vacuum

cleaner for dust extraction purposes. Connect

the tube of the dust extraction device with the

angle adapter

; see also Figure F.

NOTE: We recommend the use of a dust ex-

traction device

up to a drill size of 13 mm.

j If it is necessary to use the reducer piece

push the reducer piece into the adapter for ex-

ternal vacuum extraction

j To dismantle, proceed in reverse order to what

is described above.

First use

Switching on and oﬀ

When operating the hammer - action drill you can

select between intermittent or continuous operation

mode.

To switch on intermittent operation mode:

j Press the ON / OFF switch

To switch off intermittent operation mode:

j Release the ON / OFF switch

Switching continuous operation on:

j Press and hold the ON / OFF switch

down

and press the locking button

To switch off continuous operation mode:

j Press and then release the ON / OFF switch

Pre - selecting the

rotational speed

With the handwheel for speed preselection

you can pre - select the rotational speed in steps.

j The rotational speed that is suitable depends

on the material that has to be processed. We

recommend you carry out tests ﬁrst to deter-

mine the best rotational speed.

Tip: These two basic rules with regard to rota-

tional speed will, however, always help you:

1. large drill diameter = lower rotational speed

and so a smaller drill diameter = higher rota-

tional speed

2. harder material = lower rotational speed

Inﬁnitely variable adjustment

of the rotational speed

The ON / OFF switch

has a variable speed

control device. Slight pressure on the ON / OFF

switch

will bring about a low rotational speed.

The rotational speed will increase the more pres-

sure you exert.

Before first use / First use

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 49374 PSB 1050 A1 Seite 41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 49374 PSB 1050 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info