Bedienungsanleitung Parkside IAN 64576 PDFP 500 A1 (Seite 33 von 45) (Englisch, Portugiesisch, Spanisch)

744931

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

33 GB/MT

dispersion and results in too rapid evaporation of

the liquid. The surfaces become rough and develop

poor adhesion properties. If the working pressure is

too low on the other hand, the paint material is not

suﬃciently atomised. Undulating surfaces and the

formation of drops are the result.

j Connect the compressed air hose with the

rapid-release coupling to the compressed air

connection

of the device. This automatically

locks into place.

j Use the ﬁlter pressure reducer of the compressed

air source to set the working pressure to 3 bar.

Preparing the spraying surface

j Mask oﬀ the surroundings of the spraying sur-

face thoroughly over a wide area. Otherwise

all non-covered areas or surfaces may become

soiled.

j Make sure that the spraying surface is clean,

dry and free of grease.

j Roughen smooth surfaces and then remove the

sanding dust.

Turning the device On / Oﬀ

Working Instructions:

- When working with the device you should open

the vent

- When diluting the material, make sure that the

spraying material and the dilution are suitable

for one another. If an incorrect dilution is used,

lumps may form and clog the gun as a result.

- Screw the ﬂow cup

clockwise ﬁrmly on to

the gun.

- Fill the spraying material into the ﬂow cup

and screw the lid

on tight.

- Always hold the paint spray gun at the same

distance from the object. The ideal spraying

distance is approximately 15 cm.

- Determine the appropriate settings in each

case by experimenting.

- Do not turn the device on / oﬀ when it is over

the spraying surface, but start and end the

spraying process approximately 10 cm outside

of the spraying area.

j Press the trigger

to start spraying and keep

it held down.

j In order to stop spraying, release the trigger

again.

Adjusting the paint jet

The device has the settings round and broad jet.

Round jet Broad jet

Adjusting the round jet:

j Use the round jet, for example, for small surfaces,

corners and edges.

j Turn the regulator

in a clockwise direction .

Adjusting the broad jet:

j Use the broad jet vertically and horizontally

over larger areas.

j Turn the regulator

in an anticlockwise direc-

tion

. The nozzle head

can be continuously

adjusted vertically and horizontally by turning

to the desired position.

Regulating the

quantity of paint

Note: The front locking screw is used to limit the

adjustment range of the stroke stop screw

Increasing the quantity of paint:

j Turn the stroke stop screw

in an anticlockwise

direction.

Reducing the quantity of paint:

j Turn the stroke stop screw

in a clockwise

direction.

Regulating the quantity of air

Note: It is advisable to start with the maximum

amount of air. In order to do this, open the air volume

Initial use

64576_par_Druckluft-Farbspritzpistole_content_LB5.indd 33 31.03.11 10:49

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 64576 PDFP 500 A1 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 64576 PDFP 500 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info