Bedienungsanleitung Parkside IAN 85052 PSE 2800 B2 (Seite 35 von 41) (Französisch)

745096

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

35 GB

Operation / Cleaning, maintenance, storage, transport and ordering of spare parts Cleaning, maintenance, storage, transport and ordering of spare parts

with a clean cloth or blow it down with com-

pressed air at low pressure.

We recommend that you clean the equipment

immediately after you use it.

Clean the equipment regularly with a damp

cloth and some soft soap. Do not use cleaning

agents or solvents; these may be aggressive to

the plastic parts in the equipment. Ensure that

no water can get into the interior of the equip-

ment.

Air ﬁlter

In this connection, please also read the service

information.

Clean the air ﬁlter at regular intervals, and re-

place it if necessary.

Open both clips (Fig. J/J1) and remove the air

ﬁlter cover (Fig. J/J2).

Remove the ﬁlter elements (Fig. K/K1)

Do not use abrasive cleaning agents or petrol

to clean the elements.

Clean the elements by tapping them on a ﬂat

surface. In cases of stubborn dirt ﬁrst clean

with soapy water, then rinse with clear water

and air-dry.

Assemble in reverse order.

Spark plug (Fig. L - M)

Check the spark plug for dirt and grime after

20 hours of operation and if necessary clean it

with a copper wire brush. Thereafter service the

spark plug after every 50 hours of operation.

Pull oﬀ the spark plug boot (Fig. L) by twisting.

Remove the spark plug (Fig. M/M1) with the

supplied spark plug wrench

Assemble in reverse order.

Changing the oil and

checking the oil level

(before using the equipment)

The motor oil is best changed when the motor is at

working temperature.

Only use motor oil (15 W 40).

Place the generator on a slightly inclined sur-

face so that the oil drainage screw

is at the

lower end.

Open the oil ﬁller screw

Open the oil drainage screw and let the hot

engine oil drain out into a drip tray.

After the old oil has drained out, close the oil

drainage screw and place the generator on a

level surface again.

Fill in engine oil up to the top mark on the oil

dip stick (approx. 0.6 liters).

IMPORTANT! Do not screw the dipstick (oil

ﬁller screw) in to check the oil level, simply

insert it up to the thread.

Dispose of the waste oil properly.

Low oil switch-oﬀ

The low oil switch-oﬀ responds, if not enough en-

gine oil is present. In this case, the engine will not

start or switches oﬀ automatically after a short pe-

riod of operation. A restart will only be possible af-

ter topping-up the oil level (see Chapter „Changing

the oil and checking the oil level (before using the

equipment)“).

Preparing the equipment

for long-term storage

Warning: Do not empty the petrol tank in en-

closed areas, near ﬁre or when smoking. Petrol

fumes can cause explosions and ﬁre.

Empty the petrol tank using a petrol suction

pump.

Petrol and oil have to be disposed oﬀ accor-

ding to the regulations. Please inform yourself,

where a suitable collection point is near you.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 85052 PSE 2800 B2 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 85052 PSE 2800 B2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info