Bedienungsanleitung Parkside IAN 85053 PESG 120 A1 (Seite 48 von 58) (Deutsch, Englisch, Holländisch, Französisch)

745090

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

- 48 -

Mains connection: .........................230 V ~ 50 Hz

Welding current (A) at cos Ê = 0.73: ...... 40 - 80

ø (mm) ..............................1,6 ...........2,0 ...........2,5

.......................................40 ............55 ............80

(s) ..................................217 ...........116 ............64

(s) ............................... 1450 ........ 1381 ........ 1351

Idling voltage (V): ..............................................48

Power input: .............4 kVA at 80 A cos Ê = 0.73

Fuse (A): ............................................................... 13

Weight: ....................................................... 10.6 kg

The welding times apply for an ambient tempera-

ture of 40° C.

6. Assembling the welding

screen

(Fig. 3-9)

•

Place the welding glass (l) and the transparent

safety glass (m) over it in the frame for the

safety glass (k) (Fig. 3).

•

Press the safety glass retaining pins (q) into

the holes in welding screen frame (s) from the

outside. (Fig. 4)

•

Place the frame for the safety glass (k) with

the welding glass (l) and transparent safety

glass (m) from the inside into the recess in the

welding frame (s), press the safety glass retai-

ning bushes (n) onto the safety glass retaining

pins (q) until they engage to secure the frame

for the safety glass (k). The transparent safety

glass (m) must be on the outside. (Fig. 5)

•

Bend the top of the welding screen frame (s)

inwards (Fig. 6/1) and fold down the top

corners (Fig. 6/2). Now bend the outer sides

of the welding screen frame (s) inwards (Fig.

6/3) and connect them by pressing the top

corners and outer sides together. When the

retaining pins engage, you should be able to

hear 2 clear clicks on each side (Fig. 6/4).

•

When the top corners of the welding screen

are connected as shown in Figure 7, place

the screws for the handle (p) from the outside

through the three holes in the welding screen.

(Fig. 8)

•

Turn over the welding screen and place the

handle (r) over the threads on the three screws

for the handle (p). Secure the handle (r) to

the welding screen using the three nuts for the

handle (o). (Fig. 9)

7. Welding preparations

Connect the earth terminal (4) direct to the part

to be welded or to the support on which the part

is resting. Ensure that the earth terminal is in direct

contact with the part to be welded. You should

therefore avoid coated surfaces and/or insula-

ted materials. The electrode holder cable has a

special clamp (electrode holder (5)) at one end,

which is used to secure the electrode. The welding

screen (8) must be used at all times for welding. It

protects your eyes from the radiation emitted by

the arc and nevertheless enables you to watch the

welding process.

8. Welding

After you have made all the electrical connections

for the power supply and for the welding circuit,

you can proceed as follows:

Insert the unsheathed end of the electrode into the

electrode holder (5) and connect the earth termi-

nal (4) to the part you wish to weld. Ensure that a

good electric contact is made.

Switch on the welding set at the ON/OFF switch

(3) and set the welding current using the setting

wheel (6) to suit the electrode you wish to use.

Hold the welding screen in front of your face and

rub the tip of the electrode on the part you wish

to weld as if you were striking a match. This is the

best method of igniting the arc.

Check on a test part that you have the correct

electrode and current strength.

Electrode (Ø mm):................... Welding current (A)

1.6 ........................................................................40

2 ...........................................................................55

2.5 ........................................................................80

Anl_1549051.indb 48Anl_1549051.indb 48 17.10.12 16:1217.10.12 16:12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 85053 PESG 120 A1 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info