Bedienungsanleitung Parkside IAN 89570 PDEXS 150 A1 (Seite 43 von 51) (Französisch)

745094

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

43 GB

Introduction

Introduction / Safety instructions

Sound pressure level: 95 dB(A)

Uncertainty K: 2.5 dB

Values determined in

accordance with:

EN ISO 15744

Weight: 970 g

Wear ear protection!

Vibration emission value = 16.98 m / s

uncertainty K = 1.34 m / s

Values determined in accordance with

EN ISO 28927-3, EN 12096

The noise levels given in these instructions have

been measured in accordance with a standardised

measurement procedure speciﬁed in EN ISO 15

744

and can be used to compare appliances. Diﬀerent

uses of the pressurised air tool give rise to diﬀerent

noise levels and in some cases they may exceed

the values given in these instructions. It is easy to

underestimate the noise load if the compressed air

tool is used regularly under those circumstances.

Note: For an accurate assessment of the noise

loads experienced during a particular work period,

you should also take into account the intervening

periods of time when the appliance is switched oﬀ

or is running but is not actually in use. This can re-

sult in a much lower noise load over the whole of

the work period.

Safety instructions

Please read all safety in-

formation and instructions. Failure to comply

with the safety advice and instructions can result in

severe injuries and / or damage to property.

For future reference keep all the safety

advice and instructions in a safe place.

Check the appliance for damage be-

fore bringing it into use. Do not use the

appliance if you discover any defects.

Keep children and other per-

sons away from the appliance

during use. Distractions can cause

you to lose control of the appliance.

Do not soak materials or areas that

are to be worked on with liquids con-

taining solvents.

Avoid sanding of paints containing

lead or other material detrimental to

your health.

Do not work on materials containing

asbestos. Asbestos is considered carcinogenic.

Avoid contact with the running sanding

disc.

Only use the appliance with the

attached sanding disc.

Always keep the device clean, dry

and free of oil or grease.

Keep your workplace clean. Material

mixtures are particularly dangerous. Aluminium

dust can burn or explode.

Secure the work-piece firmly. Use clamps

or a vice to firmly hold the work-piece. This

results in a safer grip than with your hand.

Under no circumstances should you

place your hands next to or in front of

the appliance or on the area to be

worked, you could be seriously injured if the

appliance slips.

Ensure that nobody is endangered by

flying sparks. Remove combustible materi-

als from the immediate vicinity. Flying sparks

are produced when metals are ground.

Introduce the appliance to the work-

piece when it is switched on. When the

task is complete, lift the appliance from the

work-piece and then switch it off.

Let the switched off appliance come

to a complete standstill before putting

it down.

After every use check the speed and

the noise level.

Check speed regularly.

ATTENTION! Clean the appliance before

89570_par_Druckluft_Exzenterschleifer_content_LB2.indd 43 29.05.13 17:33

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 89570 PDEXS 150 A1 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 89570 PDEXS 150 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info