745115
46
Zoom out
Zoom in
Vorherige Seite
1/54
Nächste Seite
GB
- 46 -
Sound and vibration
Sound and vibration values were measured in ac-
cordance with ISO 15744 and ISO 28927-10.
L
pA
sound pressure level ...........................84 dB(A)
K
pA
uncertainty .................................................3 dB
L
WA
sound power level ............................95 dB(A)
K
WA
uncertainty ................................................3 dB
Wear ear-muffs.
The impact of noise can cause damage to hea-
ring.
Vibrations
Vibration emission value a
h
= 9.5 m/s
2
K uncertainty = 1.44 m/s
2
Warning!
The specifi ed vibration value was established in
accordance with a standardized testing method.
It may change depending on how the equipment
is used and may exceed the specifi ed value in
exceptional circumstances.
The specifi ed vibration value can be used to com-
pare the equipment with another tool.
The specifi ed vibration value can be used for initi-
al assessment of a harmful effect.
Keep the noise emissions and vibrations
to a minimum.
Only use appliances which are in perfect
working order.
Service and clean the appliance regularly.
Adapt your working style to suit the appli-
ance.
Do not overload the appliance.
Have the appliance serviced whenever ne-
cessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
Residual risks
Even if you use the equipment in ac-
cordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connec-
tion with the equipment’s construction
and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Air supply:
Via a compressed air source with pressure setting
function, e.g. a compressor. Before starting up,
please also read section 7 “Care and mainte-
nance”.
Performance values of the compressor:
The compressor used should have a tank volume
of at least 50 liters and a motor rating of approx.
2.2 kW.
Setting values for work with the suction
spray gun:
Set a maximum working pressure of 6.3 bar at
your compressed air supply.
6. Before starting the
equipment
Fig. 3
Screw the supplied nipple (4) into the air connec-
tion after you have wound 2-3 layers of sealing
tape around the thread. Plug the required chisel
into the hexagon mount of the chisel hammer. Slip
the tensioning spring (5) over the chisel. Turn the
tensioning spring onto the thread of the cylinder
(1) as far as the stop. As you do this, hold the ten-
sioning spring by the front arm.
Connect the chisel hammer to a compressor or
compressed air network with matching power. Do
this with a fl exible compressed air hose
Anleitung_4139031_LB2.indb 46Anleitung_4139031_LB2.indb 46 04.03.13 13:1604.03.13 13:16
46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside IAN 89573 PDMH 4500 A2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info