Bedienungsanleitung Parkside IAN 89573 PDMH 4500 A2 (Seite 47 von 54) (Deutsch, Englisch, Holländisch, Französisch)

745115

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

- 47 -

(Ø 10 mm internal) with quick-lock coupling.

Make sure that the air regulation screw (3) is

adjusted so that air can ﬂ ow through. Move the

chisel hammer towards the object you want to

work on. Actuate the trigger lever (2) to start the

chisel hammer.

Check the equipment and the mounted tool each

time before use. This also includes checking the

speed and the level of vibrations.

To change the chisel you must ﬁ rst disconnect the

equipment from the compressed air source. Turn

the tensioning spring off the cylinder of the chisel

hammer by holding it by its rear arm. The chisel

can now be changed as described above.

The chisel shaft should be lubricated with a little

normal lubricating grease from time to time.

7. Maintenance and care

Important: Disconnect the equipment from the

compressed air supply before you carry out any

maintenance or cleaning work.

Personal safety equipment such as gloves and

a protective dust mask must also be worn when

you carry out servicing or cleaning work on the

machine in order to prevent danger from dust

deposits.

Compliance with the maintenance instructions lis-

ted here will help this quality product provide you

with a long service life and trouble-free operation.

Clean the equipment thoroughly and immediately

each time after it has been used.

Regular lubrication is essential for your chisel

hammer to work properly for a prolonged peri-

od of time. Use only special compressed air oil

as supplied. Special compressed air oil is also

available from your dealer.

Note: Use environmentally friendly compressed

air oil if you want to operate the equipment out-

side the workshop.

The following lubrication options are available:

7.1 Lubrication by mist oiler

Connect a complete conditioning unit with mist

oiler between the compressed air source and the

chisel hammer. A conditioning unit is available

from your dealer. It is not included in the scope of

this delivery.

7.2 Lubrication by hand

Each time before using the compressed air tool

insert 3-5 drops of special compressed air oil into

the compressed air connection. If the compressed

air tool has not been used for several days you

must insert 5-10 drops of special compressed

air oil into the compressed air connection before

switching on. Store your compressed air tool only

in a dry room.

7.3 Other maintenance

There are no parts inside the equipment which

require additional maintenance.

8. Excluded from the guarantee

are

•

Wear parts

•

Damage caused by too much operating pres-

sure.

•

Damage caused by non-conditioned com-

pressed air.

•

Damage caused by improper use or unautho-

rized intervention.

Anleitung_4139031_LB2.indb 47Anleitung_4139031_LB2.indb 47 04.03.13 13:1604.03.13 13:16

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 89573 PDMH 4500 A2 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info