558602
35
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
35 GB/MT
Introduction / General safety advice
14
Laser ON / OFF switch
15
Cutting depth scale
16
Riving knife
17
Auxiliary handle
18
Drive spindle
19
Mounting flange
20
Clamping flange
21
Clamping screw with plain washer
22
Riving knife mounting
23
Mounting screws
24
Adapter for vacuum sawdust removal
Q
Included items
1 Circular saw
1 Guide fence
1 Adapter for vacuum sawdust removal
1 Allen key
2 Batteries, micro AAA 1.5 V (for laser)
1 Operating instructions
Q
Technical information
Nom. power input: 1450 W
Rated voltage: 230 V
~
50 Hz
Mechanical output: 15 Nm max.
No-load speed: n
0
1800 - 5000 min
-1
Saw blade: 210 x 30 x 1.8 x 2.6 mm
Cutting depth at 90°: 0 - 75 mm
Cutting depth at 45°: 0 - 49 mm
Protection class: II /
Noise and vibration data:
Values determined in accordance with EN 60745
The sound pressure level (A-weighted) of the device
is typically 93 dB (A). Uncertainty K=3 dB. The
sound level while working can exceed 104 dB (A).
Wear ear protection!
Evaluated acceleration, typical:
Hand / arm vibration a
h
= 2,309 m / s
2
Uncertainty K = 1,5 m / s
2
WARNING! The vibration level given in
these instructions has been measured in accord-
ance with a standardised measurement procedure
specified in EN 60745 and can be used to com-
pare devices. Different uses of the device give rise
to different vibration levels and in many cases they
may exceed the values given in these instructions. It
is easy to underestimate the vibration load if the elec-
trical power tool is used regularly in particular cir-
cumstances.
Note: If you wish to make an accurate assessment
of the vibration loads experienced during a particular
period of working, you should also take into account
the intervening periods of time when the device is
switched off or is running but is not actually in use.
This can result in a much lower vibration load over
the whole of the period of working.
General safety advice
WARNING!
Read all the safety advice and
instructions! Failure to observe the safety advice
and instructions may result in electric shock, fire
and / or serious injury.
KEEP ALL THE SAFETY ADVICE AND INSTRUCTIONS
IN A SAFE PLACE FOR FUTURE REFERENCE!
1. Your working area
a) Keep your working area clean and
clutter-free. Untidy or poorly lit working ar-
eas can lead to accidents.
b)
Do not work with the device
in potentially explosive en-
vironments in which there
are inflammable liquids, gases or
dusts. Electrical power tools create sparks,
which can ignite dusts or fumes.
c)
Keep children and other
people away while you are
operating the electrical tool.
Distractions can cause you to lose control of
the device.
PHKS_1450_Content_LB5.indd 35 30.07.2008 15:15:21 Uhr
35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside KH 3141 - PHKS 1450 LASER wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Parkside KH 3141 - PHKS 1450 LASER

Parkside KH 3141 - PHKS 1450 LASER Bedienungsanleitung - Deutsch, Holländisch, Französisch - 44 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info