Bedienungsanleitung Parkside MPKZ 2000 A1 - IAN 315340 (Seite 15 von 68) (Deutsch, Englisch, Holländisch, Französisch)

706349

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

10 GB/IE/NI

• Before making a cut, check that the stop rail (16a) and the

saw blade (6) cannot collide.

• Secure the set screw (16b) again.

• Move the machine head (4) to the top position.

• Fix the rotary table (14) in the 0° position.

• Loosen the set screw (22) and use the handle (1) to angle

the machine head (4) to the left, until the pointer (19) indi-

cates the desired angle measurement on the scale (18).

• Re-tighten the set screw (22).

• Cut as described in section 8.3.

8.7 Mitre cut 0°- 45° and turntable 0°- 45°

(ﬁg. 2/4/12)

The sliding compound mitre saw can be used to make mitre

cuts to the left of 0°- 45° in relation to the work face and, at

the same time, 0° - 45° to the left or 0° - 45° to the right in

relation to the stop rail (double mitre cut).

Attention! For mitre cuts (inclined saw head), the left side of

the moveable stop rails (16a) must be ﬁxed in the outer position.

• Open the set screw (16b) for the moveable stop rail (16a)

and push the moveable stop rail (16a) outwards.

• The moveable stop rail (16a) must be ﬁxed far enough in

front of the innermost position that the distance between the

stop rail (16a) and the saw blade (6) amounts to a minimum

of 8 mm.

• Before making a cut, check that the stop rail (16a) and the

saw blade (6) cannot collide.

• Re-tighten the set screw (16b).

• Move the machine head (4) to its upper position.

• Fold the locking handle (11) upwards to loosen the rotary

table (14).

• Set the rotary table (14) to the desired angle (refer also to

point 8.4 in this regard).

• Fold the locking handle (11) downwards to secure the rotary

table (14).

• Undo the set screw (22).

• Use the handle (1) to tilt the machine head (4) to the left until

it coincides with the required angle value (in this connection

see also section 8.6).

• Re-tighten the set screw (22).

• Cut as described under section 8.3.

8.8 Limiting the cutting depth (ﬁg. 3/13)

• The cutting depth can be inﬁnitely adjusted using the screw

(24). To do this loosen the knurled nut (24a) on the screw

(24). Turn the screw (24) in or out to set the required cutting

depth. Then re-tighten the knurled nut (24a) on the screw

(24).

• Check the setting by completing a test cut.

8.9 Chip collection bag (ﬁg. 1/20)

The saw is equipped with a debris bag (17) for sawdust and chips.

Attention! The chip collection bag may only be used when cutting

wood and wood-like materials!

Squeeze together the metal ring on the dust bag and attach it

to the outlet opening in the motor area.

The debris bag (17) can be emptied by means of a zipper at

the bottom.

Connection to an external dust extractor

For dust extraction, a vacuum hose can also be connected to

the dust extraction spout.

• Connect the vacuum hose with the dust extraction spout.

• The industrial vacuum cleaner must be suitable for the mate-

rial being worked.

• When vacuuming dust that is especially detrimental to health

or carcinogenic, use a special vacuum cleaner.

8.10 Changing the saw blade (ﬁg. 1/2/14-16)

Remove the power plug!

Important!

Wear safety gloves when changing the saw blade.

Risk of injury!

• Swing the machine head (4) upwards and lock with the lock-

ing bolt (23).

• Fold the saw blade guard (5) upwards.

• Use one hand to insert the Allen key (C) in the ﬂange screw

(28).

• Firmly press the saw shaft lock (30) and slowly rotate the

ﬂange screw (28) in clockwise direction. The saw shaft lock

(30) engages after no more than one rotation.

• Now, using a little more force, slacken the ﬂange screw (29)

in the clockwise direction.

• Turn the ﬂange screw (28) right out and remove the outer

ﬂange (29).

• Take the blade (6) oﬀ the inner ﬂange (31) and pull out

downwards.

• Carefully clean the ﬂange screw (28), outer ﬂange (29) and

inner ﬂange (31).

• Fit and fasten the new saw blade (6) in reverse order.

• Important! The cutting angle of the teeth, in other words the

direction of rotation of the saw blade (6) must coincide with

the direction of the arrow on the housing.

• Before continuing your work make sure that all safety de-

vices are in good working condition.

• Important! Every time that you change the saw blade (6),

check to see that it spins freely in the table insert (10) in both

perpendicular and 45° angle settings.

• Important! The work to change and align the saw blade (6)

must be carried out correctly.

8.11 Using the laser / LED (ﬁg. 17)

Function Press the ON/OFF switch

laser/LED (33)

1x.

OFF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside MPKZ 2000 A1 - IAN 315340 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info