Bedienungsanleitung Parkside PABS 14.4 A1 - IAN 102649 (Seite 30 von 34) (Deutsch, Englisch, Französisch)

576607

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

30 GB

General safety advice for electrical power tools / Start-up

prepared for high reaction torques as they may

cause kickback. The inserted tool will jam if it is

overloaded or if it becomes stuck in the work-

piece.

When working on the device as well

as transporting or storing it, put the

rotary direction switch in the middle

position (lock). Therefore preventing the

power tool from starting unintentionally.

DANGER! Check that you will not hit

electric, gas or water lines whilst using

the power tool. Check, if need be with a

service line detector, before you start to cut or

bore into a surface.

Original accessories / tools

Use only the accessories and attachmen

detailed in the operating instructions,

or those which are compatible with

the device.

Start-up

Charging the battery pack

CAUTION! Always ensure the plug is removed

from the mains socket before inserting a battery pack

into, or removing one from, the charging station.

Never charge the battery pack if the ambient

temperature is less than 10 °C or greater than

40 °C.

1. Insert the battery pack

in the quick charger

(see Fig. C).

2. Insert the mains plug into the mains socket. The

status LED

will light up red.

3. The green charging status LED

indicates the

charging process has been completed and the

battery pack

is ready for use.

4. Slide the battery pack

into the unit.

Never charge the battery pack for a second time

immediately after a fast charging process has

been completed. This can give rise to the battery

pack becoming overcharged and to a reduced

service life of the battery and charging station.

Switch the charger oﬀ for at least 15 minutes

between two successive charging procedures.

Remove the power plug from the wall socket.

Insertion / removal of a battery

pack into the appliance

Inserting the rechargeable battery pack:

Move the rotary direction switch

into the

middle position (lock). Push the rechargeable

battery pack

into the handle until it engages.

Removing the rechargeable battery pack:

Press the release button

and remove the

rechargeable battery pack

Checking battery status

Press the battery LED

to check the battery

condition (also see main image). The battery

display LED

will indicate the status or the

remaining charge as follows:

GREEN / RED / ORANGE = maximum charge /

capacity

RED / ORANGE = medium charge / capacity

RED = weak charge – recharge battery

Changing tools

Your cordless drill has a fully automatic spindle

lock

When the motor stops the power train will lock so

that you can open the drill chuck

by turning

it.

After you have inserted the required bit and ﬁxed it

in place by turning the chuck

, you can immedi-

ately continue working. The spindle lock releases

itself automatically when the motor is started (by

operation of the ON / OFF switch

Start-up / Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PABS 14.4 A1 - IAN 102649 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info