Bedienungsanleitung Parkside PABS 14.4 A1 - IAN 102649 (Seite 31 von 34) (Deutsch, Englisch, Französisch)

576607

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

31 GB

General safety advice for electrical power tools / Start-up Start-up / Operation

Torque pre-selection

You can adjust the torque by using torque pre-se-

lection

Select a low setting for small screws, soft work

material.

Select a high setting for large screws, hard

work materials and for the extraction of screws.

For drilling, push the selector to the setting for

drilling, in that you adjust the torque pre-selector

to the position

2 Gear Drive

CAUTION! Move the gear selector switch

only after the device has come to a standstill.

Failure to observe this advice may result in damage

to the device.

In the ﬁrst gear (Gear selector switch

in Position: 1)

A speed of up to approx. 400 rpm can be achieved

and a high torque. This setting is intended for use w

ith

all screwing tasks and for accessories (see example

Fig. B).

In the second gear (Gear selector switch

in Position: 2)

It achieves a speed of up to approx. 1300 rpm, for

the carrying out of drilling tasks (see example Fig. A).

Operation

Switching ON / OFF

Switching on:

To start the appliance squeeze on the ON /

OFF switch

and then keep it pressed down.

The LED working light

comes on with a slightly

or fully pressed ON /OFF switch

and illumi-

nates the working area in poor lighting conditio

ns.

Switching off:

To stop the appliance, release the ON / OFF

switch

Setting the speed

The ON / OFF switch

has a variable speed cont

rol

device. Slight pressure on the ON / OFF switch

will cause the rotation speed to slow down. With in-

creased pressure, the rotational speed will increase.

Note: The integrated engine brake means that the

device will come to a fast standstill.

Switching direction of rotation

To switch the direction of rotation, push the

direction of rotation switch

to either the

right or to the left.

Tips and Tricks

Before you use the appliance, check to see that

he screw or drill bit is properly ﬁtted, i.e. locate

centrally in the chuck.

Screw bits are designated with their dimensions

and their shape. If you are unsure, always try

the particular screw bit out to see whether it sits

in the screw head without any free play.

Torque:

Smaller screws and bits in particular can be

easily damaged if you adjust the appliance with

too high a torque and / or rotation speed.

Hard screwdriving conditions (into metal):

Particularly high torques can occur, for example

with metal screws tightened by socket tool bits.

Select a lower rotation speed.

Soft screwdriving conditions (e.g. into

soft wood):

You should also select a low speed in order not to

damage the wood workpiece surface through con

tact with the metal screw head. Use a countersinker.

When drilling into wood, metal and other

materials, take note of the following advice:

With small diameter drill bits use a high drill

speed. For large diameter drill bits, use a low

drill speed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PABS 14.4 A1 - IAN 102649 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info