Bedienungsanleitung Parkside PAKSP 20-Li A1 - IAN 308540 (Seite 24 von 85) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

796085

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

■ 20 │ GB│IE PAKSP 20-Li A1

Fitting the dust collection bag

NOTE

► There is a risk of ﬁre when working with electrical appliances that have

a dust collection bag or can be connected to the vacuum cleaner via

a dust extraction device! Under unfavourable conditions, wood dust in

the dust collection bag may ignite spontaneously. This can happen, for

example, due to ﬂying sparks when grinding metal or metal residues in

wood. There is an increased risk if the wood dust is mixed with other

chemical substances and heat is generated by prolonged sanding.

Therefore, do not allow the workpiece to overheat and always empty

the dust collection bag or the dust bag of the vacuum cleaner before

taking a break from work.

► Check that the dust collection bag is ﬁtted correctly.

► Observe the applicable regulations in your country regarding the

materials to be worked.

♦ Press together the two fastening clips 24a on the opening of the dust

collection bag "to widen the opening.

♦ Push the dust collection bag" onto the dust extraction connection

and release the fastening clips 24a . Make sure that the zip on the dust

collection bag "is facing downwards.

Use

WARNING! RISK OF INJURY!

Always switch the appliance oﬀ and remove the battery

before carrying out any work on the appliance.

Setting the table

♦ Undo the locking screw for the table.

♦ Turn the saw at the carrying handle /to the desired position.

You can determine the set angle using the mitre scale - and the

display arrowon the table.

♦ Retighten the locking screw for the table.

Make cuts without a mitre angle

♦ If necessary, adjust the table  as described in the section "Setting the

table".

♦ Use the supplied hex key  to turn the socket head screw ! to set the

adjustable fence 3. Slide the adjustable fence 3 inwards as far as

possible. Retighten the socket head screw!.

♦ Place the workpiece to be machined up against the adjustable fence3.

Fasten it as described in the section "Clamping the workpiece".

♦ Press the On/Oﬀ switch and keep it pressed in. The saw starts up.

Then press the release button 0 and carefully lower the saw onto the

workpiece. Saw by applying moderate pressure.

♦ After completing the cut, release the On/Oﬀ switch. Allow the saw

to stop turning before moving it back to the starting position.

Carrying out mitre cuts

♦ If necessary, adjust the table  as described in the section "Setting the

table".

♦ Set the desired saw bevel inclination from 0–45°. To do this, undo the

locking screw for the bevel angle and tilt the saw to the desired

position. Retighten the locking screw. You can also check the set

inclination angle using the bevel scale 'and the bevel indicator (.

♦ Use the supplied hex key  to turn the socket head screw ! to set the

adjustable fence 3. The distance to the saw blade 6 must not exceed

8 mm. Check the setting by lowering the saw. If necessary, adapt the

tensioning clamp1to the adjustable fence 3. Retighten the socket

head screw!.

♦ Place the workpiece to be machined up against the adjustable fence3.

Fasten it as described in the section "Clamping the workpiece".

♦ Press the On/Oﬀ switch and keep it pressed in. The saw starts up.

Then press the release button 0 and carefully lower the saw onto the

workpiece. Saw by applying moderate pressure.

♦ After completing the cut, release the On/Oﬀ switch.

Allow the saw to stop turning before moving it back to the starting

position.

Cleaning and maintenance

WARNING! RISK OF INJURY!

Always switch the appliance oﬀ and remove the battery

before carrying out any work on the appliance.

■ Store the appliance and the saw blades in a dry and dust-free location.

■ The appliance must be kept clean and free of oil or grease.

■ Use a dry cloth to clean the housing.

■ Never obstruct the ventilation openings.

■ Remove any adhering sawdust with a brush.

■ Always keep the area around the blade guard clean. Remove dust and

shavings with a brush or compressed air.

NOTE

► Replacement parts not listed (such as switches) can be ordered via our

Service Hotline.

Disposal

The packaging is made from environmentally friendly material

which can be disposed of at your local recycling plant.

Do not dispose of power tools in the normal domestic

waste!

European Directive 2012/19/EU requires that worn-out power

tools are collected separately and recycled in an environmen-

tally compatible manner.

WARNING!

► Remove the battery from the appliance before disposal.

Do not dispose of batteries in your normal household

waste!

Defective or worn-out rechargeable batteries must be recycled

according to Directive 2006/66/EC. Return the battery pack

and/or the appliance via the collection facilities oﬀered.

Please contact your local authority or town council for information about

disposal options for used power tools/battery packs.

Dispose of the packaging in an environmentally friendly manner.

Note the labelling on the packaging and separate the packaging

material components for disposal if necessary. The packaging

material is labelled with abbreviations (a) and numbers (b) with

the following meanings: 1–7: plastics, 20–22: paper and cardboard,

80–98: composites.

Your local community or municipal authorities can provide

information on how to dispose of the worn-out product.

The product is recyclable, subject to extended producer respon-

sibility and is collected separately.

Parkside PAKSP 20-Li A1 - IAN 308540 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info