679415
10
Zoom out
Zoom in
Vorherige Seite
1/64
Nächste Seite
PDEXS 125 A1
GB
IE
NI
 7
Before use
Selecting the grinding disc
Metal Removal and Surface:
The rate of metal removal and the surface quality
are determined by the grain size of the grinding
disc.
Lease note that corresponding grinding discs
with different grain sizes should be used for
processing different materials.
Changing sanding sheets
The air sander is fitted with a hook and loop faste-
ning, which allows for quick and easy replacement
of sanding discs.
Lift the grinding disc at the side and pull it off
from the backing pad in order to remove it.
HINWEIS
Before securing a new sanding sheet, remove
all dust and dirt from the sander plate .
Ensure that the openings in the sanding sheet
concur with the boreholes of the sanding plate .
Dust / swarf removal by suction
WARNING!
Please note the “Safety instructions” section.
Using the internal vacuum extraction with
dust collection device (see Fig. B):
Push the exhaust air hose fully on to the
connection for dust extraction .
You have to evert the opening of the dust bag
first, so that the straps are outside. Put the
opening of the dust bag over the free end of
the exhaust air hose and fasten the dust bag
firmly in position. In this way, the dust bag
can be tied tightly to the exhaust air hose .
NOTE
Empty the dust bag in good time and re-
gularly to ensure optimum dust extraction. To
do this open the zip fastener on the underside
of the dust bag .
Topping up the oil
In order for the air sander to have a long service
life, there must always be enough pneumatic oil in
the device.
NOTE
Use safe lubricants.
When determining which lubricants to use,
you must consider the environmental, occupa-
tional, and health aspects involved.
You may ensure this in any of the following
ways:
Connect a service unit with an oiler to the
compressor.
Install a line oiler in the compressed air line or
at the compressed air device.
Put approx. 3–5 drops of pneumatic oil by
hand into the plug nipple every 15 minutes
of operation.
Preparing for use
Connecting the compressed air source
NOTE
The air sander must be operated using
cleaned and condensate-free compressed
air only and its maximum allowable working
pressure of 6.3 bar at the device must not be
exceeded.
The compressed air source must be fitted
with a (filter) pressure reducer so that the air
pressure can be regulated.
Connect the plug nipple by a quick-release
coupler to the compressed air supply.
10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PDEXS 125 A1 - AN 304779 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info