Bedienungsanleitung Parkside PDEXS 150 B2 - IAN 110141 (Seite 11 von 76) (Deutsch, Englisch, Holländisch, Französisch, Schwedisch, Finnisch)

595309

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

PDEXS 150 B2

Reﬁlling oil

To ensure that the compressed air-powered random

orbital sander remains operational for as long as

possible, make sure that there is suﬃcient pneu-

matic oil in the appliance.

The following options are available:

♦ Attach a maintenance unit with an oiler to the

compressor.

♦ Install a ﬁtted oiler into the compressed air line

or the compressor.

Add 3–5 drops of pneumatic oil into the

connector nipple

every 15 minutes of

operation.

Connecting to a compressed air source

NOTE

► Before connecting the compressed air source

– the correct working pressure (3–6 bar)

must be fully reached

– make sure that the trigger is in the upper

position

♦ Attach the appliance to a compressor by con-

necting the connector nipple

with the supply

hose of the compressed air source.

♦ To ensure that you can regulate the air pressure,

the compressed air source must be equipped

with a pressure reducer.

Handling

Switching on and oﬀ

Switching on:

♦ First press the locking mechanism forwards and

then the trigger to switch the appliance on.

Switching oﬀ:

♦ Let go of the trigger

♦ When you have ﬁnished working, disconnect

the appliance from the compressed air source.

Regulation of vibration output

■ Use the speed controller to control the air-

ﬂow and thus the vibration output (also during

operation).

■

The ideal speed depends on the material being

worked and can be determined through practical

tests.

Use the pressure reducer to set the correct working

pressure. Operate the appliance at a working pres-

sure of 6.3 bar.

Sanding

♦ Switch on the compressed air source and allow

it to run until the maximum tank pressure has

been reached.

♦ Use the pressure reducer on the compressed

air source to set the optimum working pressure.

Note that the maximum working pressure may

not be exceeded. An excessive working pressure

does not mean increased output; it merely in-

creases the air consumption and accelerates

appliance wear. Always comply with the techni-

cal information.

♦ Switch on the compressed air-powered random

orbital sander.

♦ Allow the device to reach the required speed

and adjust as necessary.

♦ Guide the compressed air-powered random

orbital sander parallel onto the workpiece.

♦ Move the appliance parallel and in ﬂat circles

or alternatively lengthwise and across the sur-

face. Use the housing

as a handle to guide

the appliance in the desired direction.

♦ Do not press the compressed air-powered ran-

dom orbital sander down. Pressing down hard

does not increase the working eﬃciency!

♦ When you have ﬁnished working, let go of the

trigger

to switch oﬀ the appliance.

♦ When you have ﬁnished working, disconnect

the appliance from the compressed air source.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDEXS 150 B2 - IAN 110141 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info