Bedienungsanleitung Parkside PDMS A1 - IAN 43105 (Seite 29 von 34) (Deutsch, Englisch, Holländisch)

595411

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

PDMS A1

■ The mini die grinder must be operated and

maintained in accordance with the recommen-

dations contained in this manual to reduce any

unnecessary increase in vibration.

■ Consumables/machine tools must be selected,

maintained and replaced in accordance with

the recommendations in this guide in order to

avoid unnecessary increase in vibration.

■ Always use a stand, a clamp or a compensation

device to support the weight of the machine.

■ Hold the machine securely but not too ﬁ rmly

while maintaining the necessary hand-reaction

force, as the vibration risk generally increases

the harder the machine is held.

■ An inadequately mounted or damaged ma-

chine tool can lead to excessive vibrations.

Additional safety instructions for

pneumatic machines

■ Compressed air can cause serious injury. Ensure

that the air supply is switched oﬀ , the hose

is not under pressure and that the machine

is disconnected from the air supply when the

machine is not in us, and also before exchang-

ing accessories or carrying out repairs. Never

aim the airﬂ ow towards yourself or any other

person.

■ Thrashing hoses can cause serious injury.

Therefore, always check that the hoses and

their ﬁ xings are not damaged or have not come

loose.

■ If universal rotary joints (claw couplings) are

used, locking pins must be used to provide pro-

tection; Whipchek® air hose restraints must be

used to provide protection in case of a failure at

the connection of the hose to the machine.

■ Ensure that the maximum permissible pressure

stated on the machine is not exceeded.

■ Never carry compressed-air-powered machines

by the hose.

Hazards caused by accessories

■ Disconnect the grinder for whetstones from the

power supply before ﬁ tting or replacing the

machine tools or accessories.

■ Use only accessories and consumables of the

size and type recommended by the manufacturer

of the grinder for whetstones.

■ Avoid direct contact with the machine tool during

and after use, since this can have heated up or

have become sharp.

■ The maximum operating speed recommended

by the manufacturer of the grinder for whetstones

must be the same or higher than the rotational

speed labelled on the machine.

■ Never ﬁ t a grinding disc, cut-oﬀ disk or milling

cutter to a grinder for whetstones. A bursting

grinding disc can lead to extremely serious

injuries or death.

■ Do not use discs which are damaged, cracked

or could have fallen down.

■ Only approved machine tools with the correct

shaft diameter may be used.

■ Please note that you must ensure that the per-

missible rotational speed of small grinding

tools is reduced due to raising the position

of the shaft between the end of the chuck

and the small grinding tool (overhang). You

must ensure that the minimum clamping

length of 10 mm is retained. (see Figure 1)

min. 10 mm

Fig. 1

■ You must be aware that there is a danger of

mismatching between the shaft diameter of the

small grinding tool and of the chuck.

IB_43105_PDMSA1_LB1.indb 26IB_43105_PDMSA1_LB1.indb 26 14.05.14 11:1314.05.14 11:13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDMS A1 - IAN 43105 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PDMS A1 - IAN 43105

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info