Bedienungsanleitung Parkside PEBS 900 SE - IAN 37835 (Seite 26 von 44) (Deutsch, Englisch, Portugiesisch, Spanisch)

679125

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

27 GB/MT

Introduction / General safety advice for electrical power tools

Included items

Check that all the items and accessories

are present immediately after unpacking

the device:

1 Belt sander PEBS 900 SE

1 Sanding belt

1 Dust collection box

1 Extraction adapter

(for external vacuum dust extraction)

1 Fixed mounting kit

1 Operating instructions

Technical information

Belt sander: Parkside PEBS 900 SE

Nominal voltage: 230 V

50 Hz

Nom. power input: 900 W

No-load belt speed: 180 - 340 m / min

No-load speed: n

345 - 645 min

-1

Sanding belt 75 x 533 mm

Protection class: II /

Noise and vibration data:

Values determined in accordance with EN 60745.

The sound pressure level (A-weighted) of the

device is typically 86 dB (A). Uncertainty K = 3 dB.

The sound level while working can exceed

100 dB (A).

Wear ear protection!

Total vibration, EN 60745:

Vibration emission value a

h,D

= 2,928 m / s

Uncertainty K < 1.5 m / s

WARNING!

The vibration level given in these

instructions has been measured in accordance with

a standardised measurement procedure speciﬁed

in EN 60745 and can be used to compare devices.

Diﬀerent uses of the device give rise to diﬀerent vibra-

tion levels and in many cases they may exceed the

values given in these instructions. It is easy to underes-

timate the vibration load if the electrical power tool is

used regularly in particular circumstances.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particu-

lar period of working, you should also take into

account the intervening periods of time when the

device is switched oﬀ or is running but is not actual-

ly in use. This can result in a much lower vibration

load over the whole of the period of working.

The PEBS 900 SE belt sander has full-wave elec-

tronics with additional control electronics, soft start

with inrush current limiting.

General safety advice for

electrical power tools

WARNING!

Read all the safety advice

and instructions! Failure to observe the safety

advice and instructions may result in electric shock,

ﬁre and / or serious injury.

KEEP ALL THE SAFETY ADVICE AND INSTRUC-

TIONS IN A SAFE PLACE FOR FUTURE REFER-

ENCE! THE TERM “ELECTRICAL TOOL” USED

IN THE SAFETY ADVICE REFERS TO ELECTRICAL

TOOLS POWERED BY MAINS ELECTRICITY (BY

MEANS OF A MAINS LEAD) AND ELECTRICAL

TOOLS POWERED BY RECHARGEABLE BATTER-

IES (WITHOUT A MAINS LEAD).

Workplace safety

a) Keep your working area clean and

well lit. Untidy or poorly lit working areas

can lead to accidents.

Do not work with the device

in potentially explosive envi-

ronments in which there

are inflammable liquids, gases or

dusts. Electrical power tools create sparks,

which can ignite dusts or fumes.

Keep children and other peo-

ple away while you are op-

erating the electrical tool.

Distractions can cause you to lose control of

the device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PEBS 900 SE - IAN 37835 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PEBS 900 SE - IAN 37835

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info