Bedienungsanleitung Parkside PEH 30 A1 - IAN 102829 (Seite 30 von 34) (Deutsch, Englisch, Französisch)

576694

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

30 GB

Preparing for use / Maintenance and cleaningPreparing for use

Switching off:

Release the ON / OFF switch

Note: For safety reasons the ON / OFF switch

cannot be locked in the ON position.

Setting the cutting depth

The rotary control

can be used to set the cutting

depth in steps from 0–3.0 mm according to the cut-

ting depth scale

Vacuum extraction of dust /

debris (see Fig. A)

DANGER OF INJURY!

Before you carry out any work on the device always

pull the mains plug out of the mains socket.

Planing debris removal port (right / left

selectable):

Release the planing debris removal port

turning it against the direction of the arrow (out

of the “Lock” position).

Pull the planing debris removal port

out of

the device.

The planing debris removal port

can be set

to face left or right in the planer.

Push the planing debris removal port

into

the device.

Lock the planing debris removal port

turning it into the “Lock” position.

External vacuum extraction:

If necessary ﬁt the reducer piece

when using

a dust extraction system, e.g. a workshop dust

extraction system.

The vacuum cleaner / dust extraction device used

must be suitable for the material being planed.

Connection:

Place the reducer piece

ﬁrmly on to the

planing debris removal port

Push the hose of a suitable dust extraction device

approved for that purpose (e.g. a workshop

vacuum cleaner) on to the planing debris remov-

al port

or the reducer piece

Removal:

Pull the hose of the dust extraction device oﬀ

the planing debris removal port

or oﬀ the

reducer piece

Pull oﬀ the reducer piece

, if ﬁtted.

Parking shoe (see Figs. B / C)

The parking shoe

allows you to lay the device

down without the risk of damaging the workpiece.

When planing, the parking shoe

swings up and

exposes the rear part of the sole

The planing process

CAUTION! DANGER OF KICKBACK!

Always switch on the device before placing it

against the workpiece.

Set the required cutting depth.

Switch on the device.

Always place the front part of the sole

down

ﬁrst on to the workpiece.

Guide the device with even forward movement

over the surface being planed.

Move the device forward at a slow rate and

ensure that the contact pressure acts evenly on

the sole

. Moving forward at too great a rate

results in a poorer surface quality and can lead

to blocking of the planing debris removal port.

Chamfering edges (see Fig. H)

The V-grooves

in the front sole

allow the de

vice

to be used for simple chamfering of workpiece edges.

Use the V-groove most appropriate to your

desired chamfer width.

Place the planer with the V-groove

on the

work-

piece edge and guide the planer along the edge.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PEH 30 A1 - IAN 102829 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info