679265
13
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
PFBS 12 B2
10 
GB
IE
NI
Charging the integrated battery
NOTE
A new battery or a battery which has not
been used for a long time will need to be
charged before first use/reuse. It will reach its
full capacity after 3–5 charge cycles.
The charging process lasts around 180
minutes.
Starting charging:
Connect the charger
to the charging socket
on the appliance.
Connect the charger
to a mains power
socket.
The battery is fully charged when the battery
LED
shows RED/ORANGE/GREEN.
Stopping charging:
Disconnect the charger
from the mains
power supply.
Disconnect the charger
from the charging
socket
on the appliance.
CAUTION!
Never recharge a battery again immediately
after charging. There is a risk that the battery
will become overcharged.
Checking the battery charge level
If the appliance is switched on, the remaining
charge will be shown on the battery LED
as
follows:
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Changing/inserting the tool/collet
chuck
Press the spindle lock and hold it down.
Turn the tensioning nut
until the lock clicks
into place.
Undo the tensioning nut
from the thread
using the combination spanner
.
Remove any attached tool.
First push the intended tool through the tensioning
nut
before inserting it into the appropriate
collet chuck
for the tool shaft.
Press the spindle lock
and hold it down.
Push the collet chuck
into the thread insert
and screw the tensioning nut
tight with the
combination spanner
.
NOTE
Use the screwdriver side of the combination
spanner
to undo and tighten the screw on
the mandrel .
Switching on and off/setting speed
range
Switching on/setting the speed range:
Set the On/Off switch
to the position "I".
Set the speed control
to a position between
"1" and "MAX".
Switching off:
Set the On/Off switch
to the position "O".
Notes on working with materials/
tools/speed range
Use the milling bits for working on steel and
iron at maximum speed.
Determine the rotational speed range for working
on zinc, zinc alloys, aluminium and copper by
trying it out on test pieces.
Use a low rotational speed for work on plastics
and materials with a low melting point.
Use a high rotational speed for working on
wood.
Carry out cleaning, polishing and buffing work
in the medium speed range.
The following are recommendations only and not
binding. When carrying out practical work, carry
out your own tests to see which tool and which
settings are ideal for the material you are working
on.
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PFBS 12 B2 - IAN 305279 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Parkside PFBS 12 B2 - IAN 305279

Parkside PFBS 12 B2 - IAN 305279 Bedienungsanleitung - Deutsch, Holländisch, Französisch - 52 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info