Bedienungsanleitung Parkside PFBS 12 B2 - IAN 305279 (Seite 11 von 36) (Englisch)

679265

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

PFBS 12 B2

■ 8

│

a) Hold the power tool ﬁrmly in both hands

and position your body and arms so they

can absorb the force of a kickback. By taking

adequate precautions, the operator can stay in

control of the kickback forces.

b) Take special care when working on corners,

sharp edges, etc. Avoid allowing the accessory

tool to bounce back from the workpiece or

jam in the workpiece. The rotating accessory

tool is more likely to jam in corners or sharp

edges or if it rebounds oﬀ them. This can cause

a loss of control or kickback.

e) Do not use toothed saw blades. Such acces-

sories often cause a kickback or loss of control

over the power tool.

d) Always move the accessory tool in the same

direction in the material in which the cutting

edge leaves the material (in other words, the

same direction in which the dust is thrown

out). Guiding the power tool in the wrong direc-

tion will cause the cutting edge of the accessory

tool to jump out of the workpiece which can

lead to the accessory tool being pulled in this

direction.

e) Always clamp the workpiece when using

rotary ﬁles, cutting discs, high-speed milling

tools or hard-metal tools. Even a minimal tilting

in the groove can cause these tools to jam and

lead to a kickback. When a cutting disc jams, it

usually breaks. When a rotary ﬁle, high-speed

milling tool or hard-metal milling tool jams, the

accessory tool can jump out of the groove and

lead to loss of control of the power tool.

Supplementary safety instructions

for grinding and abrasive cutting

Special safety instructions for grinding and

abrasive cutting:

a) Use only the grinding accessories approved

for your power tool and only for the recom-

mended applications. Example: Never grind

with the side surface of a cutting disc. Cutting

discs are designed to remove material with

the edge of the disc. Any lateral application

of force on these grinding tools can lead to

breakage.

b) For conical and straight pencil grinders, use

only undamaged mandrels of the correct

size and length and without an undercut on

the shoulder. Using an appropriate mandrel

reduces the risk of breakages.

c) Avoid cutting disc jams or excessive contact

pressure. Do not make any excessively deep

cuts. Overloading the cutting disc increases the

stress and likelihood of tilting or jamming and

thus the possibility of kickback or breakage of

the grinding tool.

d) Avoid putting your hand in the area in front

of or behind the rotating cutting disc. When

you move the cutting disc away from your hand,

it is possible, in the event of a kickback, that the

power tool (along with the rotating disc) could

be thrown out directly towards you.

e) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steady until the

disc has completely stopped turning. Never

attempt to pull a rotating cutting disc out of a

cut. This could lead to kickback. Identify and

remove the cause of the jam.

f) Do not switch the power tool back on while it

is still in the workpiece. Allow the cutting disc

to reach its full speed before you carefully

resume the cut. Otherwise, the disc may jam,

jump out of the workpiece or cause kickback.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PFBS 12 B2 - IAN 305279 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PFBS 12 B2 - IAN 305279

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info