Bedienungsanleitung Parkside PFDS 33 A1 - IAN 280331 (Seite 33 von 119) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

684857

Zoom out

Zoom in

Vorherige Seite

1/119

Nächste Seite

│

29 ■

PFDS 33 A1

Welds on an inner edge

The preparation for this weld joint is very simple and is carried out for thick-

nesses of 5 mm. The dimension “d” needs to be reduced to a minimum

and should always be less than 2 mm.

For thicker materials, however, it is no longer expedient. In this case, it is better

to prepare a joint as shown opposite in which the edge of a plate is angled.

45°45°

Overlap welds

The most usual preparation is that with straight weld edges. The weld can

be undone using a standard angle weld seam. Both workpieces must be

brought as close to each other as possible.

Cleaning and care

WARNING!

► To avoid the danger of electric shock, injury or damage:

–

Before cleaning, always disconnect the mains plug

from the mains power socket.

– Never immerse the ﬂux-core welder or the accessories

in water.

– Allow the ﬂux-core welder and accessories to cool

down before cleaning them.

– Never use abrasive, caustic or scratching cleaning

agents. These can damage the appliance.

■ Keep the ﬂux-core welder clean. Welding equipment must be kept free

of dust to ensure adequate cooling. In especially dirty air, a monthly

cleaning using compressed air is necessary.

■ Protect the ﬂux-core welder from metal dust.

■ Store the ﬂux-core welder in a dry room, secured from access by un-

authorised persons or children.

■ Ensure that the welding lead, the torch and earth clamp are all in

perfect condition.

■ Cables and current-carrying parts of the ﬂux-core welder with dam-

aged insulation are dangerous and can impair the proper functioning

of the appliance.

■ Repairs may only be carried out by authorised repair shops or similarly

qualiﬁed persons.

■ Always disconnect the appliance from the mains power supply before

all maintenance and repair work.

Wire feed

■ Regular cleaning of the wire feed drive and replacement of worn wire

feed rolls.

■ Blow out the steel core with compressed air.

■ Do not tighten the tension spring on the pressure roller too tightly. Ex-

cessive pressure lead to higher abrasion of the steel wire. The dust thus

created deposits in the guide spring and causes an uneven discharge

of the welding wire making it impossible to create an even weld.

Cable assembly

■ Protect the cable assembly from external damage.

■ Never pull it over sharp edges or other objects.

■ Never drive a vehicle over it.

■ Clean the cable assembly regularly.

■ The steel sleeve and torch nozzle are wearing parts.

■ The torch nozzle is exposed to heat radiation and friction from the wire

and must be checked and replaced regularly.

■ Weld splatter collects on the torch nozzle. This must be removed

regularly.

■ For overhead welding, frequent cleaning is necessary.

■ Use nozzle grease or nozzle spray before and after welding. This

prevents too much splatter from accumulating.

Welder

■ The transformer of the welder must be freed of accumulated dust to

ensure that the cooling works properly. In especially dirty air, a monthly

cleaning using compressed air is necessary.

■ Protect the welder from metal dust.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PFDS 33 A1 - IAN 280331 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info