Bedienungsanleitung Parkside PHKSA 12 A1 - IAN 302329 (Seite 9 von 50) (Englisch)

679113

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

PHKSA 12 A1

■ 6

│

c) Set the cutting depth to match the thickness

of the workpiece. The blade should not extend

more than one full tooth depth under the work-

piece.

d) Never hold the workpiece to be sawn in your

hand or over your leg. Fasten the workpiece

onto a stable working surface. It is important

to fasten the workpiece securely to minimise the

danger of bodily contact, jamming of the saw

blade or loss of control.

e) Hold the power tool only by the insulated

handles when you are carrying out work

in which the accessory tool may come into

contact with concealed power cables. Contact

with a live wire will also make exposed metal

parts of the power tool live and could give the

operator an electric shock.

f) When making longitudinal cuts, always use

a rip fence or a straight edge guide. This will

improve the accuracy of your cut and reduce

the likelihood of the saw blade jamming.

g) Always use saw blades of the correct size

and with an appropriate central ﬁxing bore

(e.g. diamond-shaped or circular). Blades that

do not match the mounting hardware of the saw

will run eccentrically, causing loss of control.

h) Never use damaged or incorrect blade

washers or bolts. The saw blade washers and

screws have been specially designed to provide

optimum performance and operational safety

for your saw.

Further safety instructions for all saws

Kickback – causes and corresponding safety

instructions

▯ A kickback is a sudden reaction caused as a

result of the saw blade catching, jamming or

being falsely aligned, causing the saw to jump

up uncontrollably and out of the workpiece in

the direction of the operator;

▯ if the saw blade catches or jams in a narrowing

saw cut, the blade can no longer rotate and the

power of the motor throws the appliance back

in the direction of the operator;

▯ if the saw blade twists in the saw cut or be-

comes misaligned, the teeth at the rear edge of

the saw blade can become caught in the wood

surface, causing the saw blade to jump out of

the cut and the saw to jump backwards in the

direction of the operator.

Kickback is a result of saw misuse and/or incorrect

operating procedures or conditions. This can be

avoided by taking proper precautions as given

below.

a) Hold the saw ﬁrmly and position your arms

so that they can absorb the force of a kick-

back. Always stand to the side of the saw

blade and never in line with it. If a kickback

occurs, the circular saw may jump backwards.

However, by taking appropriate precautions the

operator can control the kickback forces.

b) If the saw blade jams or you stop working,

switch the saw oﬀ and hold it steadily in the

workpiece until the saw blade has completely

stopped turning. Never attempt to remove

the saw from the workpiece or pull it back-

wards while the saw blade is still moving as

this could lead to a kickback. Investigate and

take corrective actions to eliminate the cause of

blade binding.

c) If you want to restart a saw that is still in the

workpiece, centre the saw blade in the cut

and check to ensure that the teeth are not

caught anywhere in the workpiece. If the saw

blade catches it can jump out of the workpiece

or cause a kickback when the saw is restarted.

d) Support large panels to minimise the risk of

blade pinching and kickback. Large panels

tend to bend under their own weight. Panels/

boards must be supported on both sides: i.e.

both in the vicinity of the saw cut and also at

the edge.

e) Do not use blunt or damaged saw blades.

Saw blades with blunt or misaligned teeth may

cause excessive friction as the saw cut is too

narrow, and this can cause a saw blade jam

and kickback.

f) Before sawing, ensure that the fastenings for

the cut depth and cut angle settings are tight-

ened. If the settings change while sawing, the

IB_302329_PHKSA12A1_LB6-.indb 6 29.03.18 13:44

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PHKSA 12 A1 - IAN 302329 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PHKSA 12 A1 - IAN 302329

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info