Bedienungsanleitung Parkside PKO 24 A1 - IAN 339151 (Seite 19 von 80) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

786099

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

14 GB/IE

6. Safety information

m Attention!

The following basic safety measures must be observed when

using electric tools for protection against electric shock, and the

risk of injury and ﬁre. Read all these notices before using the

electric tool and keep the safety instructions for later reference.

Safe work

1. Keep the work area orderly

- Disorder in the work area can lead to accidents.

2. Take environmental inﬂuences into account

- Do not expose electric tools to rain.

- Do not use electric tools in a damp or wet environment.

There is a risk of electric shock!

- Make sure that the work area is well-illuminated.

- Do not use electric tools where there is a risk of ﬁre or

explosion.

3. Protect yourself from electric shock

- Avoid physical contact with earthed parts (e. g. pipes,

radiators, electric ranges, cooling units).

4. Keep children away

- Do not allow other persons to touch the equipment or

cable, keep them away from your work area.

5. Securely store unused electric tools

- Unused electric tools should be stored in a dry, elevated

or closed location out of the reach of children.

6. Do not overload your electric tool

- They work better and more safely in the speciﬁed output

range.

7. Wear suitable clothing

- Do not wear wide clothing or jewellery, which can be-

come entangled in moving parts.

- Rubber gloves and non-slip shoes are recommended

when working outdoors.

- Tie long hair back in a hair net.

8. Do not use the cable for purposes for which it is not in-

tended

- Do not use the cable to pull the plug out of the outlet.

Protect the cable from heat, oil and sharp edges.

9. Take care of your tools

- Keep your compressor clean in order to work well and

safely.

- Follow the maintenance instructions.

- Check the connection cable of the electric tool regularly

and have it replaced by a recognised specialist when

damaged.

- Check extension cables regularly and replace them

when damaged.

10. Pull the plug out of the outlet

- During non-use of the electric tool or prior to mainte-

nance and when replacing tools such as saw blades,

bits, milling heads.

11. Avoid inadvertent starting

- Make sure that the switch is switched oﬀ when plugging

the plug into an outlet.

12. Use extension cables for outdoors

- Only use approved and appropriately identiﬁed exten-

sion cables for use outdoors.

- Only use cable reels in the unrolled state.

13. Remain attentive

- Pay attention to what you are doing. Remain sensible

when working. Do not use the electric tool when you

are distracted.

14. Check the electric tool for potential damage

- Protective devices and other parts must be carefully in-

spected to ensure that they are fault-free and function as

intended prior to continued use of the electric tool.

- Check whether the moving parts function faultlessly and

do not jam or whether parts are damaged. All parts

must be correctly mounted and all conditions must be

fulﬁlled to ensure fault-free operation of the electric tool.

- Damaged protective devices and parts must be properly

repaired or replaced by a recognised workshop, insofar

as nothing diﬀerent is speciﬁed in the operating manual.

- Damaged switches must be replaced at a customer ser-

vice workshop.

- Do not use any faulty or damaged connection cables.

- Do not use any electric tool on which the switch cannot

be switched on and oﬀ.

15. Have your electric tool repaired by a qualiﬁed electrician

- This electric tool conforms to the applicable safety regu-

lations. Repairs may only be performed by an electri-

cian using original spare parts. Otherwise accidents can

occur.

16. Important!

- For your own safety you must only use the accessories

and additional units listed in the operating instructions or

recommended or speciﬁed by the manufacturer. The use

of mounted tools or accessories other than those recom-

mended in the operating instructions or catalogue may

place your personal safety at risk.

17. Noise

- Wear ear muﬀs when you use the compressor.

18. Replacing the power cable

- To prevent hazards, leave the replacement of damaged

power cables strictly to the manufacturer or a qualiﬁed

electrician. There is a risk of electric shock!

19. Inﬂating tires

- Directly after inﬂating tires, check the pressure with a suit-

able pressure gauge, for example at your ﬁlling station.

20. Roadworthy compressors for building site operations

- Make sure that all lines and ﬁttings are suitable for the

maximum permissible operating pressure of the com-

pressor.

21. Place of installation

- Set up the compressor on an even surface.

22. Supply hoses at pressures above 7 bar should be equipped

with a safety cable (e. g. a wire rope).

23. Avoid over-stressing the piping system by using ﬂexible

hose connections to prevent kinking.

24. Ensure that oil cooling devices are kept clean.

25. Risk of burns from hot oil

-Wear suitable protective gloves.

-Never work with the compressor near naked ﬂames.

-Be careful not to spill oil.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKO 24 A1 - IAN 339151 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info