Bedienungsanleitung Parkside PKO 270 A1 - IAN 89564 (Seite 37 von 46) (Deutsch, Englisch, Holländisch)

595282

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

- 37 -

4. Proper use

The compressor is designed to generate com-

pressed air for compressed-air driven tools which

can be driven with an air volume of up to approx.

270 l/min (e.g. tire inﬂ ator, blow-out pistol and

paint spray gun). Due to the limited air output it is

not possible to use the compressor to drive tools

with very high air consumption (for example or-

bital sanders, rod grinders and hammer screwdri-

vers).

The equipment is to be used only for its prescribed

purpose. Any other use is deemed to be a case of

misuse. The user / operator and not the manufac-

turer will be liable for any damage or injuries of

any kind caused as a result of this.

Please note that our equipment has not been de-

signed for use in commercial, trade or industrial

applications. Our warranty will be voided if the

machine is used in commercial, trade or industrial

businesses or for equivalent purposes.

5. Technical data

Mains connection: .........................230 V ~ 50 Hz

Motor rating kW: ........................................ 1.8 kW

Operating mode: ................................................S1

Compressor speed min

-1

: .............................. 2850

Operating pressure bar: ..............................max. 8

Pressure vessel capacity (in liters): .....................24

Theoretical intake capacity (l/min): . approx. 270

Sound power level L

in dB: ............................94

uncertainty: ...............................................4 dB

Protection type: ................................................IP20

Weight of the unit in kg: ......................................26

Oil (15W 40): ..................................................0.3 l

The noise emission values were measured in ac-

cordance with EN ISO 2151.

6. Before starting the

equipment

Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

•

Check the equipment for damage which may

have occurred in transit. Report any damage

immediately to the transport company which

was used to deliver the compressor.

•

Install the compressor near the point of con-

sumption.

•

Avoid long air lines and supply lines (extensi-

on cables).

•

Make sure that the intake air is dry and dust-

free.

•

Do not install the compressor in a damp or

wet room.

•

The compressor may only be used in suitable

rooms (with good ventilation and an ambient

temperature from +5 °C to 40 °C). There must

be no dust, acids, vapors, explosive gases or

inflammable gases in the room.

•

The compressor is designed to be used in dry

rooms. It is prohibited to use the compressor in

areas where work is conducted with sprayed

water.

•

The oil level in the compressor pump has to

be checked before putting the equipment into

operation (see 9.4).

Anleitung_4010360_LB1.indb 37Anleitung_4010360_LB1.indb 37 17.01.13 12:4217.01.13 12:42

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKO 270 A1 - IAN 89564 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PKO 270 A1 - IAN 89564

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info