Bedienungsanleitung Parkside PKO 270 A1 - IAN 89564 (Seite 38 von 46) (Deutsch, Englisch, Holländisch)

595282

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

- 38 -

7. Assembly and starting

 Important!

Remove the transportation braces (bet-

ween the compressor pump and clad-

ding, see Fig. 7) prior to initial start-up.

If the transportation braces are not re-

moved, heat can build up and cause the

compressor to ignite.

 Important!

You must fully assemble the appliance

before using it for the ﬁ rst time!

You will require the following tools for assembly

and installation:

2 x open-ended wrench size 13 mm (not inclu-

ded)

7.1 Fitting the wheels (11)

Fit the supplied wheels as shown in Figure 5.

7.2 Fitting the supporting foot (8)

Fit the supplied supporting foot as shown in Figure

7.3 Fitting the air ﬁ lter (15)

Remove the transportation stop (B) and screw the

air ﬁ lter (15) to the equipment. (Fig. 7, 8).

7.4 Changing the transportation cover (A)

Remove the transportation cover from the oil ﬁ ller

opening (21) and insert the supplied oil sealing

plug (16) into the oil ﬁ ller opening. (Fig. 9, 10.)

7.5 Mains connection

•

The compressor is equipped with a mains

cable with shock-proof plug. This can be

connected to any 230V ~ 50 Hz shock-proof

socket which is protected by a 16 A fuse.

•

Before you use the machine, make sure that

the mains voltage is the same as the operating

voltage (see the rating plate).

•

Long supply cables, extensions, cable reels

etc. cause a drop in voltage and can impede

motor start-up.

•

At low temperatures below +5°C, sluggish-

ness may make starting difficult or impossible.

7.6 ON/OFF switch (Fig. 2)

Pull the ON/OFF switch (17) upwards to switch

on the compressor. To switch off the compressor,

press the ON/OFF switch down.

7.7 Setting the pressure (Fig. 1-3)

•

Use the pressure regulator (3) to set the pres-

sure on the pressure gauge (5).

•

The set pressure can be drawn from the quick-

lock coupling (4).

•

The vessel pressure can be read off the pres-

sure gauge (6).

•

The vessel pressure is drawn from the quick-

lock coupling (20).

7.8 Setting the pressure switch (Fig. 1)

The pressure switch (2) is set at the factory.

Cut-in pressure approx. 6 bar

Cut-out pressure approx. 8 bar

7.9 Fitting the compressed air hose

(Fig. 1, 3)

Use the compressed air hose (14) if you intend

to carry out work at a greater distance from the

compressor. To do so, connect the nipple (H)

on the compressed air hose to one of the quick-

release couplings (4, 20). Then attach the com-

pressed air tool to the quick-release coupling (G)

on the compressed air hose.

8. Replacing the power cable

If the power cable for this equipment is damaged,

it must be replaced by the manufacturer or its

after-sales service or similarly trained personnel to

avoid danger.

Anleitung_4010360_LB1.indb 38Anleitung_4010360_LB1.indb 38 17.01.13 12:4217.01.13 12:42

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKO 270 A1 - IAN 89564 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PKO 270 A1 - IAN 89564

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info