Bedienungsanleitung Parkside PKO 270 A2 - IAN 275673 (Seite 39 von 44) (Deutsch, Englisch, Holländisch, Französisch)

668306

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

40 GB

When the oil has drained out, re-ﬁt the oil drain plug (12).

Dispose of the old oil at a drop-off point for old oil.

To ﬁll in the correct quantity of oil, make sure that the

compressor stands on an even surface. Fill new oil through

the oil ﬁller opening (21) until it comes up to the maximum

level. This is marked with a red dot on the oil level window

(18) (Fig. 11). Do not exceed the maximum ﬁlling quantity.

Overﬁlling the equipment may result in damage. Reinsert

the oil sealing plug (16) into the oil ﬁller opening (21).

10.6 Cleaning the intake ﬁlter (Fig. 3, 12, 13)

The intake ﬁlter prevents dust and dirt being drawn in. It is

essential to clean this ﬁlter after at least every 300 hours in

service. A clogged intake ﬁlter will decrease the compres-

sor’s performance dramatically. Open the thumb screw (E)

to the remove the intake ﬁlter.

Then pull off the ﬁlter cover (C). Now you can remove the

air ﬁlter (F) and the ﬁlter housing (D). Carefully tap out the

air ﬁlter, ﬁlter cover and ﬁlter housing. Then blow out these

parts with compressed air (approx. 3 bar) and reinstall in

reverse order.

12. Troubleshooting

Fault Possible cause Remedy

The compressor does not

start.

• No supply voltage.

• Insufﬁcient supply voltage.

• Outside temperature is too low.

• Motor is overheated.

• Check the supply voltage, the power plug and the

socket-outlet.

• Make sure that the extension cable is not too long.

Use an extension cable with large enough wires.

• Never operate with an outside temperature of below

+5° C.

• Allow the motor to cool down. If necessary, remedy

the cause of the overheating.

The compressor starts but

there is no pressure.

• The non-return valve (19) leaks.

• The seals are damaged.

• The drain plug for condensation water (10)

leaks.

• Have a service center replace the non-return valve

(19).

• Check the seals and have any damaged seals

replaced by a service center.

• Tighten the screw by hand. Check the seal on the

screw and replace if necessary.

The compressor starts,

pressure is shown on the

pressure gauge, but the

tools do not start.

• The hose connections have a leak.

• A quick-lock coupling has a leak.

• Insufﬁcient pressure set on the pressure regula-

tor (5).

• Check the compressed air hose and tools and

replace if necessary.

• Check the quick-lock coupling and replace if neces-

sary.

• Increase the set pressure with the pressure regulator.

10.7 Storage

m Important!

Pull out the mains plug and ventilate the equipment

and all connected pneumatic tools. Switch off the com-

pressor and make sure that it is secured in such a way

that it cannot be started up again by any unauthor-

ized person.

m Important!

Store the compressor only in a dry location which is

not accessible to unauthorized persons. Always store

upright, never tilted! Oil may leak out!

10.7.1 Releasing excess pressure

Release the excess pressure by switching off the compressor

and using the compressed air which is still left in the pres-

sure vessel, e.g. with a compressed air tool running in idle

mode or with a blow-out pistol.

11. Disposal and recycling

The equipment is supplied in packaging to prevent it from

being damaged in transit. The raw materials in this pack-

aging can be reused or recycled. The equipment and its

accessories are made of various types of material, such as

metal and plastic. Defective components must be disposed

of as special waste. Ask your

dealer or your local council.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKO 270 A2 - IAN 275673 Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info