Bedienungsanleitung Parkside PKO 270 A2 - IAN 275673 (Seite 37 von 44) (Deutsch, Englisch, Holländisch, Französisch)

668306

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

38 GB

7. Before starting the equipment

Before you connect the equipment to the mains supply

make sure that the data on the rating plate are identical to

the mains data.

• Check the equipment for damage which may have oc-

curred in transit. Report any damage immediately to

the transport company which was used to deliver the

compressor.

• Install the compressor near the point of consumption.

• Avoid long air lines and supply lines (extension cables).

• Make sure that the intake air is dry and dustfree.

• Do not install the compressor in a damp or wet room.

• The compressor may only be used in suitable rooms

(with good ventilation and an ambient temperature from

+5 °C to 40 °C). There must be no dust, acids, vapors,

explosive gases or inﬂammable gases in the room.

• The compressor is designed to be used in dry rooms. It

is prohibited to use the compressor in areas where work

is conducted with sprayed water.

• The oil level in the compressor pump has to be checked

before putting the equipment into operation.

8. Attachment and operation

m Important!

You must fully assemble the appliance before using it

for the ﬁrst time!

You will require the following tools for assembly and instal-

lation: 2 x open-ended wrench size 17 mm (not included)

8.1 Fitting the wheels (Fig. 5)

• Fit the supplied wheels as shown.

8.2 Fitting the supporting foot (Fig. 6)

• Fit the supplied supporting foot as shown.

8.3 Fitting the air ﬁlter (Fig. 7,8)

• Remove the transportation stop (B) and screw the air ﬁl-

ter (15) to the equipment.

8.4 Changing the transportation cover (A) (Fig. 9,10)

• Remove the transportation cover from the oil ﬁlter open-

ing (21) and insert the supplied oil sealing plug (16) into

the oil ﬁller opening.

8.5 Mains connection

• The compressor is equipped with a mains cable with

shock-proof plug. This can be connected to any 230-

240V ~ 50 Hz shock-proof socket.

• Before you use the machine, make sure that the mains

voltage is the same as the operating voltage (see the

rating plate).

• Long supply cables, extensions, cable reels etc. cause a

drop in voltage and can impede motor start-up.

• At low temperatures below +5°C, sluggishness may

make starting difﬁcult or impossible.

8.6 ON/OFF switch (Fig. 2)

• Pull the ON/OFF switch (17) upwards to switch on the

compressor. To switch off the compressor, press the

ON/OFF switch down.

8.7 Setting the pressure (Fig. 1,3)

• Use the pressure regulator (5) to set the pressure on the

pressure gauge (4).

• The set pressure can be drawn from the quick lock cou-

pling (3).

• The vessel pressure can be read off the pressure gauge

(6).

• The vessel pressure is drawn from the quick lock cou-

pling (7).

8.8 Setting the pressure switch (Fig. 1)

• The pressure switch (2) is set at the factory.

Cut-in pressure approx. 6 bar

Cut-out pressure approx. 8 bar.

8.9 Fitting the compressed air hose (Fig. 1, 3)

• Use the compressed air hose (14) if you intend to carry

out work at a greater distance from the compressor. To

do so, connect the nipple (H) on the compressed air

hose to one of the quick release couplings (3, 7). Then

attach the compressed air tool to the quick-release cou-

pling (I) on the compressed air hose.

8.10 Overload switch (Fig. 14)

The motor is ﬁtted with an overload switch (20). If the

compressor overloads, the overload switch switches off the

equipment automatically to protect the compressor from

overheating. If the overload switch triggers, switch off the

compressor using the ON/ OFF switch (17) and wait until

the compressor cools down. Then press the overload switch

(20) and restart the compressor.

9. Electrical connection

The electrical motor installed is connected and ready

for operation. The connection complies with the appli-

cable VDE and DIN provisions.

The customer‘s mains connection as well as the exten-

sion cable used must also comply with these regula-

tions.

• The product meets the requirements of EN 61000-3-

11 and is subject to special connection conditions. This

means that use of the product at any freely selectable

connection point is not allowed.

• Given unfavourable conditions in the power supply the

product can cause the voltage to ﬂuctuate temporarily.

• The product is intended solely for use at connection

points that

a) do not exceed a maximum permitted supply imped-

ance “Z” (Zmax = 0.382 Ω), or

b) have a continuous current-carrying capacity of the

mains of at least 100 A per phase.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKO 270 A2 - IAN 275673 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info