Bedienungsanleitung Parkside PKO 270 A3 - IAN 285200 (Seite 12 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

668290

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

12 GB/IE/NI

9. Electrical connection

The electrical motor installed is connected and ready

for operation. The connection complies with the appli-

cable VDE and DIN provisions.

The customer‘s mains connection as well as the exten-

sion cable used must also comply with these regula-

tions.

Important information

In the event of an overloading the motor will switch itself off.

After a cool-down period (time varies) the motor can be

switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is often dam-

aged.

This may have the following causes:

• Passage points, where connection cables are passed

through windows or doors.

• Kinks where the connection cable has been improperly

fastened or routed.

• Places where the connection cables have been cut due

to being driven over.

• Insulation damage due to being ripped out of the wall

outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not be

used and are life-threatening due to the insulation damage.

Check the electrical connection cables for damage regu-

larly. Make sure that the connection cable does not hang on

the power network during the inspection.

Electrical connection cables must comply with the applica-

ble VDE and DIN provisions. Only use connection cables

with the marking „H05VV-F“.

The printing of the type designation on the connection

cable is mandatory.

AC motor

• The mains voltage must be 220 - 240 V~ 50 Hz.

• Extension cables up to 25 m long must have a cross-

section of 1.5 mm

Connections and repairs of electrical equipment may only

be carried out by an electrician.

Please provide the following information in the event of any

enquiries:

• Type of current for the motor

• Machine data - type plate

10. Cleaning, maintenance, and storage

m Important!

Pull out the power plug before doing any cleaning and

maintenance work on the equipment. Risk of injury from

electric shock!

m Important!

Wait until the equipment has cooled down completely! Risk

of burns!

m Important!

Always depressurize the equipment before carrying out any

cleaning and maintenance work! Risk of injury!

10.1 Cleaning

• Keep the equipment free of dirt and dust as far as pos-

sible. Wipe the equipment with a clean cloth or blow it

down with compressed air at low pressure.

• We recommend that you clean the equipment immedi-

ately after you use it.

• Clean the equipment regularly with a damp cloth and

some soft soap. Do not use cleaningagents or solvents;

these may be aggressive to the plastic parts in the

equipment. Ensure that no water can get into the interior

of the equipment.

• You must disconnect the hose and any spraying tools

from the compressor before cleaning. Do not clean the

compressor with water, solvents or the like.

10.2 Maintenance work on the pressure vessel (Fig. 1)

m Important! To ensure a long service life of the pressure

vessel (8), drain off the condensed water by opening the

drain valve (10) each time after using. Release the vessel

pressure ﬁrst (see 10.7.1). Open the drain screw by turning

counter-clockwise (looking at the screw from the bottom

of the compressor) so that all the condensed water can run

out of the pressure vessel. Then close the drain screw again

(turn it clockwise). Check the pressure vessel for signs of

rust and damage each time before using. Do not use the

compressor with a damaged or rusty pressure vessel. If you

discover any damage, then please contact the customer

service workshop.

m Important!

The condensed water from the pressure vessel will

contain residual oil. Dispose of the condensed water

in an environmentally compatible manner at a suita-

ble collection point.

10.3 Safety valve (Fig. 3)

The safety valve (19) has been set for the highest permitted

pressure of the pressure vessel. It is prohibited to adjust the

safety valve or remove its seal. Actuate the safety valve

from time to time to ensure that it works when required. Pull

the ring with sufﬁcient force until you can hear the com-

pressed air being released. Then release the ring again.

10.4 Checking the oil level at regular intervals (Fig. 11)

Place the compressor on a level and straight surface. The oil

level must be between the MAX and MIN marks on the oil

level window (18).

Oil change: we recommend SAE 15W 40 or equivalent.

The original oil ﬁlling must be changed after 100 hours in

operation; thereafter the oil must be drained and replaced

with new oil after every 500 hours in operation.

10.5 Changing the oil (Fig. 1,10,11)

Switch off the engine and pull the mains plug out of the

socket. Remove the oil sealing plug (16). After releasing any

air pressure you can unscrew the oil drain plug (12) from the

compressor pump (13).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKO 270 A3 - IAN 285200 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info