Bedienungsanleitung Parkside PKO 270 A3 - IAN 285200 (Seite 11 von 64) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

668290

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

11GB/IE/NI

6. Technical data

Mains connection 220 - 240 V ~ 50Hz

Motor rating W

1800

Operating mode

Compressor speed

2850 min

-1

Pressure vessel capacity (in liters)

approx. 24

Operating pressure

approx. 10 bar

Theoretical intake capacity (l/min)

approx. 260

sound power level L

97 dB(A)

uncertainty K

3 dB

Protection type

IP20

Weight of the unit in kg

approx. 27

Oil (15W 40) l

approx. 0,6

Max. altitude

(above mean sea level)

1000 m

The noise emission values were measured in accordance

with EN ISO 3744:1995.

Wear hearing protection.

The effects of noise can cause a loss of hearing.

7. Before starting the equipment

Before you connect the equipment to the mains supply

make sure that the data on the rating plate are identical to

the mains data.

• Check the equipment for damage which may have oc-

curred in transit. Report any damage immediately to

the transport company which was used to deliver the

compressor.

• Install the compressor near the point of consumption.

• Avoid long air lines and supply lines (extension cables).

• Make sure that the intake air is dry and dustfree.

• Do not install the compressor in a damp or wet room.

• The compressor may only be used in suitable rooms

(with good ventilation and an ambient temperature from

+5 °C to 40 °C). There must be no dust, acids, vapors,

explosive gases or inﬂammable gases in the room.

• The compressor is designed to be used in dry rooms. It

is prohibited to use the compressor in areas where work

is conducted with sprayed water.

• The oil level in the compressor pump has to be checked

before putting the equipment into operation.

8. Attachment and operation

m Important!

You must fully assemble the appliance before using it

for the ﬁrst time!

You will require the following tools for assembly and instal-

lation: Open-ended wrench size 12, 13 and 14 mm (not

included)

8.1 Fitting the wheels (Fig. 4,5)

• Fit the supplied wheels as shown.

8.2 Fitting the supporting feet (Fig. 4,6)

• Fit the supplied supporting foot as shown.

8.3 Fitting the air ﬁlter (Fig. 7,8)

• Remove the transportation stop (B) and screw the air ﬁl-

ter (15) to the equipment.

8.4 Changing the transportation cover (A) (Fig. 9,10)

• Remove the transportation cover from the oil ﬁlter open-

ing (20) and insert the supplied oil sealing plug (16)

into the oil ﬁller opening.

8.5 Mains connection

• The compressor is equipped with a mains cable with

shock-proof plug. This can be connected to any 220 -

240 V~ 50 Hz shock-proof socket.

• Before you use the machine, make sure that the mains

voltage is the same as the operating voltage (see the

rating plate).

• Long supply cables, extensions, cable reels etc. cause a

drop in voltage and can impede motor start-up.

• At low temperatures below +5°C, sluggishness may

make starting difﬁcult or impossible.

8.6 ON/OFF switch (Fig. 2)

• Pull the ON/OFF switch (17) upwards to switch on the

compressor. To switch off the compressor, press the

ON/OFF switch down.

8.7 Setting the pressure (Fig. 1,3)

• Use the pressure regulator (5) to set the pressure on the

pressure gauge (4).

• The set pressure can be drawn from the quick lock cou-

pling (3).

• The vessel pressure can be read off the pressure gauge

(6).

• The vessel pressure is drawn from the quick lock cou-

pling (7).

8.8 Setting the pressure switch (Fig. 1)

• The pressure switch (2) is set at the factory.

Cut-in pressure approx. 8 bar

Cut-out pressure approx. 10 bar.

8.9 Fitting the compressed air hose (Fig. 1, 3)

• Use the compressed air hose (14) if you intend to carry

out work at a greater distance from the compressor. To

do so, connect the nipple (H) on the compressed air

hose to one of the quick release couplings (3, 7). Then

attach the compressed air tool to the quick-release cou-

pling (I) on the compressed air hose.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKO 270 A3 - IAN 285200 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info