Bedienungsanleitung Parkside PKO 270 A5 - IAN 315462 (Seite 11 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

773324

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

7GB/IE/NI

Damaged electrical connection cable

The insulation on electrical connection cables is often dam-

aged.

This may have the following causes:

• Passage points, where connection cables are passed through

windows or doors

• Kinks where the connection cable has been improperly fas-

tened or routed

• Places where the connection cables have been cut due to

being driven over

• Insulation damage due to being ripped out of the wall outlet

• Cracks due to the insulation ageing

Such damaged electrical connection cables must not be used

and are life-threatening due to the insulation damage.

Check the electrical connection cables for damage regularly.

Make sure that the connection cable does not hang on the

power network during the inspection.

Electrical connection cables must comply with the applicable

VDE and DIN provisions. Only use connection cables with the

marking „H05VV-F“.

The printing of the type designation on the connection cable

is mandatory.

AC motor

The mains voltage must be 220-240 V~.

• Extension cables up to 25 m long must have a cross-section

of 1.5 mm2.

Connections and repairs of electrical equipment may only be

carried out by an electrician.

Please provide the following information in the event of any

enquiries:

• Type of current for the motor

• Machine data - type plate

10. Cleaning, maintenance, and storage

m Important!

Pull out the power plug before doing any cleaning and mainte-

nance work on the equipment. Risk of injury from electric shock!

m Important!

Wait until the equipment has cooled down completely! Risk of

burns!

m Important!

Always depressurize the equipment before carrying out any

cleaning and maintenance work! Risk of injury!

10.1 Cleaning

• Keep the equipment free of dirt and dust as far as possible.

Wipe the equipment with a clean cloth or blow it down with

compressed air at low pressure.

• We recommend that you clean the equipment immediately

after you use it.

• Clean the equipment regularly with a damp cloth and some

soft soap. Do not use cleaning agents or solvents; these may

be aggressive to the plastic parts in the equipment. Ensure

that no water can get into the interior of the equipment.

• You must disconnect the hose and any spraying tools from

the compressor before cleaning. Do not clean the compres-

sor with water, solvents or the like.

10.2 Maintenance work on the pressure vessel

(ﬁg. 1)

Important! To ensure a long service life of the pressure ves-

sel (8), drain oﬀ the condensed water by opening the drain

valve (10) each time after using. Release the vessel pressure

ﬁrst (see 10.7.1). Open the drain screw by turning counter-

clockwise (looking at the screw from the bottom of the compres-

sor) so that all the condensed water can run out of the pressure

vessel. Then close the drain screw again (turn it clockwise).

Check the pressure vessel for signs of rust and damage each

time before using.

Do not use the compressor with a damaged or rusty pressure

vessel. If you discover any damage, then please contact the

customer service workshop.

m Important!

The condensed water from the pressure vessel will contain re-

sidual oil. Dispose of the condensed water in an environmen-

tally compatible manner at a suitable collection point.

10.3 Safety valve (ﬁg. 3)

The safety valve (19) has been set for the highest permitted

pressure of the pressure vessel. It is prohibited to adjust the

safety valve or remove its seal. Actuate the safety valve from

time to time to ensure that it works when required. Pull the ring

with suﬃcient force until you can hear the compressed air being

released. Then release the ring again.

10.4 Checking the oil level at regular intervals

(ﬁg. 11)

Place the compressor on a level and straight surface.

The oil level must be between the MAX and MIN marks on the

oil level window (18).

Oil change: we recommend SAE 15W 40 or equivalent. The

original oil ﬁlling must be changed after 100 hours in opera-

tion; thereafter the oil must be drained and replaced with new

oil after every 500 hours in operation.

10.5 Changing the oil (ﬁg. 1, 10, 11)

Switch oﬀ the engine and pull the mains plug out of the socket.

Remove the oil sealing plug (16). After releasing any air pres-

sure you can unscrew the oil drain plug (12) from the compres-

sor pump (13).

To prevent the oil from running out in an uncontrolled manner,

hold a small metal chute under the opening and collect the oil

in a vessel. If the oil does not drain out completely, we recom-

mend tilting the compressor slightly. When the oil has drained

out, re-ﬁt the oil drain plug (12).

Dispose of the old oil at a drop-oﬀ point for old oil.

To ﬁll in the correct quantity of oil, make sure that the compres-

sor stands on an even surface. Fill new oil through the oil ﬁller

opening (20) until it comes up to the maximum level. This is

marked with a red dot on the oil level window (18) (ﬁg. 11).

Do not exceed the maximum ﬁlling quantity. Overﬁlling the

equipment may result in damage. Reinsert the oil sealing plug

(16) into the oil ﬁller opening (20).

Parkside PKO 270 A5 - IAN 315462 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PKO 270 A5 - IAN 315462

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info