Bedienungsanleitung Parkside PKO 400 B2 - IAN 89566 (Seite 51 von 62) (Deutsch, Englisch, Holländisch, Französisch)

668298

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

- 51 -

6. Before starting the

equipment

Before you connect the equipment to the mains

supply make sure that the data on the rating plate

are identical to the mains data.

•

Check the equipment for damage which may

have occurred in transit. Report any damage

immediately to the transport company which

was used to deliver the compressor.

•

Install the compressor near the point of con-

sumption.

•

Avoid long air lines and supply lines (extensi-

on cables).

•

Make sure that the intake air is dry and dust-

free.

•

Do not install the compressor in a damp or

wet room.

•

The compressor may only be used in suitable

rooms (with good ventilation and an ambient

temperature from +5 °C to 40 °C). There must

be no dust, acids, vapors, explosive gases or

inflammable gases in the room.

•

The compressor is designed to be used in dry

rooms. It is prohibited to use the compressor in

areas where work is conducted with sprayed

water.

•

The oil level in the compressor pump has to

be checked before putting the equipment into

operation (see 9.4).

7. Assembly and starting

 Important!

You must fully assemble the appliance

before using it for the ﬁ rst time!

You will require the following tools for assembly

and installation:

•

1 x open-ended wrench size 13 mm (not in-

cluded)

•

2 x open-ended wrench size 16 mm (not in-

cluded)

7.1 Fitting the wheels (11)

Fit the supplied wheels as shown in Figure 5.

7.2 Fitting the supporting feet (8)

Fit the supplied supporting feet as shown in

Figure 6.

7.3 Fitting the air ﬁ lters (15)

Remove the transportation stopper (B) and screw

the air ﬁ lters (15) securely to the equipment (Fig.

7, 8). Make sure that the intake opening on the air

ﬁ lter faces down.

7.4 Changing the transportation cover (A)

Remove the transportation cover from the oil ﬁ ller

opening (21) and insert the supplied oil sealing

plug (16) into the oil ﬁ ller opening. (Fig. 9, 10.)

7.5 Mains connection

•

Before you use the machine, make sure that

the mains voltage is the same as the operating

voltage (see the rating plate).

•

Long supply cables, extensions, cable reels

etc. cause a drop in voltage and can impede

motor start-up.

•

At low temperatures below +5°C, sluggish-

ness may make starting difficult or impossible.

7.6 ON/OFF switch (Fig. 2)

Pull the ON/OFF switch (17) upwards to switch

on the compressor. To switch off the compressor,

press the ON/OFF switch down.

7.7 Setting the pressure (Fig. 1-3)

•

Use the pressure regulator (3) to set the pres-

sure on the pressure gauge (5).

•

Turn the pressure regulator knob to adjust the

pressure.

•

The set pressure can be drawn from the quick-

lock coupling (4).

•

The vessel pressure can be read off the pres-

sure gauge (6).

•

The vessel pressure is drawn from the quick-

lock coupling (20).

Anl_4010162.indb 51Anl_4010162.indb 51 25.03.13 15:5025.03.13 15:50

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKO 400 B2 - IAN 89566 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info