Bedienungsanleitung Parkside PKO 400 B2 - IAN 89566 (Seite 52 von 62) (Deutsch, Englisch, Holländisch, Französisch)

668298

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

- 52 -

7.8 Setting the pressure switch (Fig. 1)

The pressure switch (2) is set at the factory.

Cut-in pressure approx. 6 bar

Cut-out pressure approx. 8 bar

7.9 Overload cut-out (Fig. 3)

The motor of this equipment is protected against

overload by an overload switch (G). If the rated

current is exceeded, the overload switch (G) will

shut down the equipment. After a short cooling

down period, the equipment can be switched on

again by pressing the overload switch (G).

8. Replacing the power cable

If the power cable for this equipment is damaged,

it must be replaced by the manufacturer or its

after-sales service or similarly trained personnel to

avoid danger.

9. Cleaning, maintenance,

storage, ordering spare

parts and transport

 Important!

Pull out the power plug before doing any

cleaning and maintenance work on the

equipment. Risk of injury from electric

shock!

 Important!

Wait until the equipment has cooled

down completely! Risk of burns!

 Important!

Always depressurize the equipment be-

fore carrying out any cleaning and main-

tenance work (see 9.7.1)! Risk of injury!

9.1 Cleaning

•

Keep the equipment free of dirt and dust as

far as possible. Wipe the equipment with a

clean cloth or blow it down with compressed

air at low pressure.

•

We recommend that you clean the equipment

immediately after you use it.

•

Clean the equipment regularly with a damp

cloth and some soft soap. Do not use cleaning

agents or solvents; these may be aggressive

to the plastic parts in the equipment. Ensure

that no water can get into the interior of the

equipment.

•

You must disconnect the hose and any

spraying tools from the compressor before

cleaning. Do not clean the compressor with

water, solvents or the like.

9.2 Maintenance work on the pressure

vessel (Figure 1)

Important! To ensure a long service life of the

pressure vessel (7), drain off the condensed water

by opening the drain valve (9) each time after

using. Release the vessel pressure ﬁ rst (see 9.7.1).

Open the drain screw by turning counter-clock-

wise (looking at the screw from the bottom of the

compressor) so that all the condensed water can

run out of the pressure vessel. Then close the drain

screw again (turn it clockwise). Check the pressure

vessel for signs of rust and damage each time

before using. Do not use the compressor with a

damaged or rusty pressure vessel. If you discover

any damage, then please contact the customer

service workshop.

 Important!

The condensed water from the pressure

vessel will contain residual oil. Dispose

of the condensed water in an environ-

mentally compatible manner at a suitable

collection point.

Anl_4010162.indb 52Anl_4010162.indb 52 25.03.13 15:5025.03.13 15:50

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKO 400 B2 - IAN 89566 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info