Bedienungsanleitung Parkside PKS 1500 A1 - IAN 93463 (Seite 12 von 52) (Deutsch, Englisch, Holländisch, Französisch)

706390

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

7GB/IE

m Assembly

WARNING! For you own safety, only insert the mains

plug in an outlet when all assembly steps have been

completed and you have read and understood the

safety and operating instructions.

Lift the saw out of the packaging and place it on your

work bench. (Positioning of the saw on the work bench

- see the next page under „POSITIONING / WORK STA-

TION“)

Installation of the dust bag

• Squeeze together the metal ring on the dust bag (12)

and attach it to the outlet opening in the motor area.

Assembling the work piece clamping device (g. 1.1)

• Loosen the locking screw (17) and attach the work

piece clamping device (10) to the left or right of the

xed saw bench.

• Afterwards, retighten the locking screws (17).

Assembling the work piece supports (g. 1.1 – 1.2)

• Loosen the cross-head screw (14) and guide the work

piece support through the specied hole on the side of

the xed saw bench.

• Make sure that the work piece support (15) is also

guided through the two plates (19) on the underneath.

• Afterwards, retighten the cross-head screw (14).

• Repeat this process on the other side.

Assembling the support stand (g. 1.1 – 1.2)

• Loosen the cross-head screws (18) on the underneath

of the saw and guide the support stand (16) through

the specied holes on the back of the saw.

• Afterwards, retighten the cross-head screws (18).

m Area of application

Intended application possibilities

The machine cuts:

• Wood and materials similar to wood

• Plastic

Unintended application possibilities

The machine is not suitable for:

• Ferritic materials, steel and cast iron, as well as other

material types which are not listed, particularly food.

• Mitre saw without guard.

• Materials larger than the specied cutting data:

90°/90°/ 120 x 60 mm

90°/45° 80 x 60 mm

45°/90° 120 x 35 mm

45°/45° 80 x 35 mm

Settings

CROSS-CUTTING

ATTENTION: Before carrying out the following adjust-

ments, please check whether the motor of the machine

is switched off.

Pivoting the table plate (Fig. 2)

The mitre saw can be pivoted left and right with the rota-

ry table. Exact angle adjustment is possible on the basis

of the scale. The angle can be precisely and quickly ad-

justed from 0° to 45° with locking positions at 15°, 22.5°

and 30°.

To pivot the rotary table, loosen the set screw (21) and

rotate the unit using the handle (20) until the desired

angle is reached. Then secure it with the set screw (21).

Tilt of the saw unit (Fig. 3)

The saw unit can be tilted at an angle of up to 45°.

Loosen the handle (23) on the rear side of the machine

and tilt the unit to the desired angle position according to

the scale. The angle can be set on the basis of the scale

(24) using the pointer (25). Then the handle must be re-

tightened.

Working instructions

After you have carried out all the tasks described above,

you can begin working.

ATTENTION: Always keep your hands away from the

cutting zone and never attempt to reach in while cutting.

FIXING A WORKPIECE

Clamp the work piece on the work table with the workpi-

ece clamp (10 - Fig 1) in order to x it in place.

Cross-cutting (Fig. 4)

• Loosen the locking knob (26).

• Lift the saw unit by the handle (2) until it locks in place

in the top position

• Press the workpiece evenly on the stop strips (27);

make sure that you hand remains outside the cutting

area of the saw blade.

• With your right hand on the handle (2), press the lo-

cking lever (3) so that the unit can also be pivoted

downward.

• The motor starts when the start button (1) is pressed.

• Slowly bring the saw blade down to the workpiece and

cut through it with moderate pressure.

• Pivot the unit back to the upper starting position into

it locks in place.

• Release the handle (2) so that the motor switches off.

Saw blade replacement (Fig. 5)

• Pull out the mains plug.

• Place the saw unit in „cross-cutting“ position

• Unlock the moving saw blade guard (6) by pressing

the lock (3 - Fig. 1); in the process, raise the saw bla-

de guard so that the saw blade is free.

• Actuate the spindle lock (22 - Fig. 3).

• Loosen the saw blade fastening screw (28) - (Atten-

tion: left-handed thread).

• Remove the screw (28) and saw blade ange (29).

• Carefully remove the saw blade (risk of injury from the

saw blade teeth).

• Place a new saw blade on the inner saw blade an-

ge. In the process, observe the rotational direction of

the saw blade.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKS 1500 A1 - IAN 93463 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info