Bedienungsanleitung Parkside PKS 1500 A1 - IAN 93463 (Seite 13 von 52) (Deutsch, Englisch, Holländisch, Französisch)

706390

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

8 GB/IE

• Fit the outer saw blade ange and rmly tighten the

screw.

• Move the saw blade guard back to the correct position.

Replacing laser batteries (Fig. 6)

• Remove the laser battery cover (30). Remove the 2

batteries.

• Replace both batteries with the same or an equivalent

type. Make sure that they are inserted with the same

polarity as the used batteries.

• Close the battery cover.

switch ON / switch OFF the laser

To switch on: Move the ON/OFF switch of the laser

(34) to the “1” position. A laser line is projected onto the

material you wish to process, providing an exact guide

for the cut.

To switch off: Move the ON/OFF switch of the laser to

the “0” position.

m Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies with

the applicable VDE and DIN provisions.

The customer‘s mains connection as well as the

extension cable used must also comply with these

regulations.

Important information

In the event of an overloading the motor will switch its-

elf off. After a cool-down period (time varies) the motor

can be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is often

damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been impro-

perly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insulation

damage.

Check the electrical connection cables for damage re-

gularly. Make sure that the connection cable does not

hang on the power network during the inspection.

Electrical connection cables must comply with the ap-

plicable VDE and DIN provisions. Only use connection

cables with the marking „H 07 RN“.

The printing of the type designation on the connection

cable is mandatory.

AC motor

• The mains voltage must be 230 V~

• Extension cables up to 25 m long must have a

cross-section of 1.5 mm2.

Connections and repairs of electrical equipment

may only be carried out by an electrician.

Please provide the following information in the event of

any enquiries:

• Type of current for the motor

• Machine data - type plate

Accessories

SAW DUST EXTRACTION

The mitre saw is equipped with an extraction port to

which an extraction system can be connected. Alterna

tively, a dust bag can also be attached.

The hose of the extraction system is fastened on the ex

traction port with a clamp. We recommend emptying the

bag or container from time to time and cleaning the lter.

The air speed of the suction system must be at least 30

metres per second.

m Maintenance

If personnel qualied for unusual maintenance tasks

or repairs must be obtained during of after the war-

ranty period, please always contact a service point

recommended by us or contact the manufacturer.

• Only perform repair, maintenance and cleaning work

as well as the correction of malfunctions with the drive

switched off as a basic rule.

• All protective and safety equipment must be reassem-

bled immediately after repair, maintenance is com-

pleted.

NORMAL SERVICE TASKS

Normal service tasks can also be performed by untrai-

ned personnel and are all described in the preceding

sections and in this chapter.

• The mitre saw must not be lubricated, because it al-

ways cuts dry surfaces; all moving machine parts are

self-lubricating.

• In the event of service work, personal protective

equipment must always be work (protective goggles

and gloves).

• Remove saw dust and chips regularly by cleaning the

cutting zone and support surfaces.

We recommend using a suction tool or brush.

ATTENTION: Do not use compressed air!

Check the saw blade from time to time: If problems ari-

se with the blade, it must be ground by a specialist or

replaced, depending on the condition.

DECOMMISSIONING OF THE MACHINE

After the machine is decommissioned it can be disposed

of with normal industrial waste.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKS 1500 A1 - IAN 93463 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info