Bedienungsanleitung Parkside PKS 1500 A2 - IAN 290768 (Seite 23 von 92) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

706358

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

GB/IE18

5 Do not mix old and new batteries or batteries of dif-

ferent types or manufacturers! Replace an entire set of

batteries at the same time.

6 Immediately remove used batteries from the device and

dispose of them properly! Do not dispose batteries with

household waste. Defective or used batteries must be

recycled according to Directive 2006/66 / EC.

Give back batteries and / or the device has been of-

fered to the collective facilities. About disposal facilities

you can inform by your municipal or city government.

7 Do not allow batteries to heat up!

8 Do not weld or solder directly on batteries!

9 Do not dismantle batteries!

10 Do not allow batteries to deform!

11 Do not throw batteries into ﬁre!

12 Keep batteries out of the reach of children.

13 Do not allow children to replace batteries without

supervision!

14 Do not keep batteries near ﬁre, ovens or other sources

of heat. Do not use batteries in direct sunlight or store

them in vehicles in hot weather.

15 Keep unused batteries in the original packaging

and keep them away from metal objects. Do not mix

unpacked batteries or toss them together! This can

lead to a short-circuit of the battery and thus damage,

burns or even the risk of ﬁre.

16 Remove batteries from the equipment when it will not

be used for an extended period of time, unless it is for

emergencies!

17 NEVER handle batteries that have leaked without

appropriate protection. If the leaked ﬂuid comes into

contact with your skin, the skin in this area should be

rinsed oﬀ under running water immediately. Always

prevent the ﬂuid from coming into contact with the

eyes and mouth. In the event of contact, please seek

immediate medical attention.

18 Clean the battery contacts and corresponding con-

tacts in the device prior to inserting the batteries.

Residual risks

The machine has been built according to the

state of the art and the recognised technical

safety requirements. However, individual

residual risks can arise during operation.

• Health hazard due to electrical power, with the use of

improper electrical connection cables.

• Furthermore, despite all precautions having been met,

some non-obvious residual risks may still remain.

• Residual risks can be minimised if the “Important informa-

tion”, „Additional safety instructions“ and the „Proper

use“ are observed along with the whole of the operating

instructions.

• Do not load the machine unnecessarily: excessive pres-

sure when sawing will quickly damage the saw blade,

which results in reduced output of the machine in the pro-

cessing and in cut precision.

• When cutting plastic material, please always use clamps:

the parts which should be cut must always be ﬁxed be-

tween the clamps.

• Avoid accidental starting of the machine: the operating but-

ton may not be pressed when inserting the plug in an outlet.

• Use the tool that is recommended in this manual. In do-

ing so, your mitre saw provides optimal performance.

• Hands may never enter the processing zone when the

machine is in operation.

• Release the handle button and switch oﬀ the machine

prior to any operations.

Assembly

WARNING! For you own safety, only insert

the mains plug in an outlet when all as-

sembly steps have been completed and you

have read and understood the safety and

operating instructions.

Lift the saw out of the packaging and place it on your work

bench. (Positioning of the saw on the work bench - see the

next page under „POSITIONING / WORK STATION“)

Installation of the dust bag (fig. 2)

• Squeeze together the metal ring on the chip bag (12)

and attach it to the outlet opening in the motor area.

Assembling the work piece clamping de-

vice (fig. 1.1)

• Loosen the locking screw (17) and attach the work piece

clamping device (10) to the left or right of the ﬁxed saw bench.

• Afterwards, retighten the locking screws (17).

Assembling the work piece supports (fig.

1.1 – 1.2)

• Loosen the cross-head screw (14) and guide the work

piece support through the speciﬁed hole on the side of

the ﬁxed saw bench.

• Make sure that the work piece support (15) is also

guided through the two plates (19) on the underneath.

• Afterwards, retighten the cross-head screw (14).

• Repeat this process on the other side.

Assembling the support stand (fig. 1.1 – 1.2)

• Loosen the cross-head screws (18) on the underneath of

the saw and guide the support stand (16) through the

speciﬁed holes on the back of the saw.

• Afterwards, retighten the cross-head screws (18).

Commissioning

Prior to commissioning, observe the safety

instructions in the operating instructions.

REMOVAL FROM THE PACKAGING

Remove the machine from its package, which protects it during

transport, without damaging the package in order to be able to

use it later for transporting the mitre saw for long-term storage.

MOVING

Since the mitre saw is relatively small and light, its location

can be easily changed, even by a single person. After lock-

ing the locking knob (26 - Fig. 4) in the bottom position, lift

the mitre saw by the handle (34 - Fig. 4).

Parkside PKS 1500 A2 - IAN 290768 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info