Bedienungsanleitung Parkside PKS 1500 A2 - IAN 290768 (Seite 25 von 92) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

706358

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

GB/IE20

• The motor starts when the start button (1) is pressed.

• Slowly bring the saw blade down to the workpiece and

cut through it with moderate pressure.

• When the cutting operation is completed, move the ma-

chine head back to its upper (home) position and release

the ON/OFF button (1).

Attention! The machine executes an upward stroke automati-

cally due to the return spring, i.e. do not release the handle (2)

after completing the cut; instead allow the machine head to

move upwards slowly whilst applying light counter pressure.

Mitre cut 0°- 45° (Fig. 1, 1.3, 3)

The crosscut saw can be used to make mitre cuts of 0° -

45° in relation to the work face.

Important! To make miter cuts (inclined saw head), the

adjustable stop rail (27a) must be ﬁxed at the outer position.

• Open the set screw (27b) for the adjustable stop rail

(27a) with an Allen key and push the adjustable stop rail

outwards.

• The adjustable stop rail (27a) must be ﬁxed far enough in

front of the innermost position that the distance between

the stop rail (27a) and the saw blade (5) amounts to a

maximum of 8 mm.

• Before making a cut, check that the stop rail (27a) and

the saw blade (5) cannot collide.

• Secure the locking lever (27b) again.

• Move the machine head to the top position.

• Fix the rotary table (9) in the 0° position.

• Loosen the set screw (23) and use the handle (2) to angle

the machine head to the left, until the pointer (25) indi-

cates the desired angle measurement on the scale (24).

• Re-tighten the ﬁxing screw (23).

• Cut as described in section “Cross-cutting”.

Mitre cut 0°- 45° and turntable 0°- 45°

The crosscut saw can be used to make mitre cuts to the left

of 0°- 45° in relation to the work face and, at the same

time, 0° - 45° to the left or 0° - 45° to the right in relation

to the stop rail (double mitre cut).

Important! To make miter cuts (inclined saw head), the

adjustable stop rail (27a) must be ﬁxed at the outer position.

• Open the set screw (27b) for the adjustable stop rail

(27a) with an Allen key and push the adjustable stop rail

outwards.

• The adjustable stop rail (27a) must be ﬁxed far enough in

front of the innermost position that the distance between

the stop rail (27a) and the saw blade (5) amounts to a

maximum of 8 mm.

• Before making a cut, check that the stop rail (27a) and

the saw blade (5) cannot collide.

• Secure the locking lever (27b) again.

• Move the machine head to its upper position.

• Release the rotary table (9) by loosening the set screw (23).

• Using the handle (2), set the rotary table (9) to the desired angle.

• Retighten the set screw (23) in order to secure the rotary table.

• Undo the locking screw (23) and use the handle (2) to

tilt the machine head to the left until it coincides with the

required angle value.

• Retighten the ﬁxing screw (23).

• Cut as described in section “Cross-cutting”.

Saw blade replacement (Fig. 5)

• Pull out the mains plug.

• Place the saw unit in „cross-cutting“ position

• Unlock the moving saw blade guard (6) by pressing the

locking lever (3 - Fig. 1); in the process, raise the saw

blade guard so that the saw blade is free.

• Actuate the spindle lock (22 - Fig. 3).

• Loosen the saw blade fastening screw (28) - (Atten-

tion: left-handed thread).

• Remove the screw (28) and saw blade ﬂange (29).

• Carefully remove the saw blade (risk of injury from the

saw blade teeth).

• Place a new saw blade on the inner saw blade ﬂange. In the

process, observe the rotational direction of the saw blade.

• Fit the outer saw blade ﬂange and ﬁrmly tighten the screw.

• Move the saw blade guard back to the correct position.

Replacing laser batteries (Fig. 6)

• Remove the laser battery cover (30). Remove the 2 batteries.

• Replace both batteries with the same or an equivalent

type. Make sure that they are inserted with the same po-

larity as the used batteries.

• Close the battery cover.

Switch ON / switch OFF the laser (Fig. 6)

To switch on: Move the ON/OFF (33) switch of the

laser (34) to the “1” position. A laser line is projected onto

the material you wish to process, providing an exact guide

for the cut.

To switch off: Move the ON/OFF switch of the laser

to the “0” position.

Adjusting the laser (Fig. 7)

If the laser (31) ceases to indicate the correct cutting line, you

can readjust the laser. To do so, open the screws (32) and set

the laser by moving sideways to that the laser beam strikes the

teeth of the saw blade (5).

Electrical connection

The electrical motor installed is connected

and ready for operation. The connection

complies with the applicable VDE and DIN

provisions. The customer‘s mains connec-

tion as well as the extension cable used

must also comply with these regulations.

Important information

In the event of an overloading the motor will switch itself

oﬀ. After a cool-down period (time varies) the motor can

be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is often damaged.

This may have the following causes:

• Passage points, where connection cables are passed

through windows or doors.

• Kinks where the connection cable has been improperly

fastened or routed.

• Places where the connection cables have been cut due

to being driven over.

Parkside PKS 1500 A2 - IAN 290768 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info