Bedienungsanleitung Parkside PKS 1700 B2 - IAN 79729 (Seite 49 von 58) (Deutsch, Englisch, Holländisch)

706392

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

- 49 -

back of the equipment (Fig. 6).

6.3 Precision adjustment of the stop for

crosscut 90° (Fig. 7-8)

•

No stop angle included.

•

Fasten the turntable (16) in 0° position.

•

Undo the locking screw (23) and move the

machine head (5) all the way to the right

using the handle (1).

•

Place the 90° angular stop (z) between the

blade (7) and the turntable (16).

•

Slacken the counternut (d). Adjust the ad-

justment screw (90°) (29) until the angle

between the blade (7) and the turntable (16)

equals 90°.

•

Retighten the counternut (d) to secure this set-

ting.

•

Check the position of the pointer (21) on the

scale (20). If necessary, release the pointer

(21) with a crosstip screwdriver, move to the

0° position of the scale (20) and retighten.

6.4 Precision adjustment of the stop for

miter cut 45° (Fig. 1, 7, 10-11)

•

No stop angle included.

•

Fasten the turntable (16) in 0° position.

•

Undo the locking screw (23) and move the

machine head (5) all the way to the left using

the handle, until it coincides at 45°.

•

Place the 45° stop angle (y) between the bla-

de (7) and the turntable (16).

•

Adjust the adjustment screw (30) so that the

angle between the blade (7) and the turntab-

le (16) equals exactly 45°.

7. Operation

7.1 Cross cut 90° and turntable 0°

(Fig. 1-3, 12)

Important! The integral resetting springs will

automatically lift the machine head. Do not simply

let go of the handle (1) after cutting, but allow the

machine head (5) to rise slowly, applying slight

counter pressure as it does so.

For cutting widths up to approx. 100 mm it is

possible to ﬁ x the saw’s drag function with the

locking screw for drag guide (24) in rear position.

If the cutting width exceeds 100 mm you must

ensure that the locking screw for drag guide (24)

is slackened and that the machine head (5) can

be moved.

•

Move the machine head (5) to its upper posi-

tion.

•

Use the handle (1) to push back the machine

head (5) and fix it in this position if required

(dependent on the cutting width).

•

Place the piece of wood to be cut at the stop

rail (19) and on the turntable (16).

•

Lock the material with the clamping device

(8) on the fixed saw table (17) to prevent the

material from moving during the cutting ope-

ration.

•

Push down the release lever (3) to release the

machine head (5).

•

Press the ON/OFF switch (2) to start the mo-

tor.

•

With the drag guide (26) fixed in place: use

the handle (1) to move the machine head (5)

steadily and with light pressure downwards

until the saw blade (7) has completely cut

through the workpiece.

•

With the drag guide (26) not fixed in place:

pull the machine head (5) all the way to the

front. Lower the handle (1) to the very bottom

by applying steady and light downward

pressure. Now push the machine head (5)

slowly and steadily to the very back until the

saw blade (7) has completely cut through the

workpiece.

•

When the cutting operation is completed,

move the machine head (5) back to its upper

(home) position and release the ON/OFF

Anl_4300685.indb 49Anl_4300685.indb 49 08.10.12 17:2308.10.12 17:23

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKS 1700 B2 - IAN 79729 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PKS 1700 B2 - IAN 79729

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info