Bedienungsanleitung Parkside PKS 1700 B2 - IAN 79729 (Seite 50 von 58) (Deutsch, Englisch, Holländisch)

706392

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

- 50 -

button (2).

7.2 Cross cut 90° and turntable 0° - 45°

(Fig. 1-3, 13)

The crosscut saw can be used to make crosscuts

of 0° -45° to the left and 0° -45° to the right in

relation to the stop rail.

•

Release the turntable (16) by slackening the

locking grip (13).

•

Press the latched position lever (12). Turn the

turntable (16) and scale pointer (14) to the

desired angular setting on the scales (15) and

lock into place with the locking grip (13). The

saw has locking positions at angles of - 45°,

-30°, -22.5°, -15°, 0°, 15°, 22.5°, 30°

and 45°, at which you can engage latched

position lever (12).

•

Cut as described under section 7.1.

7.3 Miter cut 0°- 45° and turntable 0°

(Fig. 1-3, 14)

The crosscut saw can be used to make miter cuts

of 0° - 45° in relation to the work face.

•

If required, dismantle the clamping device (8)

or mount on the opposite side of the fixed saw

table (17).

•

Move the machine head (5) to its upper posi-

tion.

•

Fasten the turntable (16) in 0° position.

•

Undo the locking screw (23). Use the handle

(1) to tilt the machine head (5) to the left until

the pointer (21) points to the required angle

on the scale (20).

•

Re-tighten the fixing screw (23).

•

Cut as described in section 7.1.

7.4 Miter cut 0°- 45° and turntable 0°-

45° (Fig. 1-3, 15)

The crosscut saw can be used to make miter cuts

to the left of 0°- 45° in relation to the work face

and, at the same time, 0° - 45° to the left or 0° -

45° to the right in relation to the stop rail (double

miter cut).

•

If required, dismantle the clamping device (8)

or mount on the opposite side of the fixed saw

table (17).

•

Move the machine head (5) to its upper posi-

tion.

•

Release the turntable (16) by slackening the

locking grip (13).

•

Press the latched position lever (12). Turn the

turntable (16) and scale pointer (14) to the

desired angular setting on the scales (15) and

lock into place with the locking grip (13).

•

Undo the locking screw (23) and use the

handle (1) to tilt the machine head (5) to the

left until it coincides with the required angle

value (in this connection see also section 7.3).

•

Re-tighten the fixing screw (23).

•

Cut as described under section 7.1.

7.5 Limiting the cutting depth (Fig. 16)

•

The cutting depth can be infinitely adjusted

using the screw (27). To do this loosen the

knurled nut on the screw (27). Move the stop

for the cutting depth limiter (28) to the outside.

Turn the screw (27) in or out to set the requi-

red cutting depth. Then re-tighten the knurled

nut on the screw (27).

•

Check the setting by completing a test cut.

7.6 Sawdust bag (Fig. 2)

The saw is equipped with a debris bag (22) for

sawdust and chips.

The debris bag (22) can be emptied by means of

a zipper at the bottom.

7.7 Changing the saw blade

(Fig. 1, 17-20)

Remove the power plug!

Important.

Wear safety gloves when changing the

saw blade. Risk of injury.

•

Swing up the machine head (5). Use the sa-

fety pin (25) to lock the machine head in this

position.

•

Press the release lever (3). Swing up the saw

blade guard (6) to the point where the recess

in the saw blade guard (6) is above the flan-

ge bolt (31).

•

Press the saw shaft lock (4) with one hand.

With the other hand insert the Allen key (c) in

the flange bolt (31).

•

Firmly press the saw shaft lock (4) and slowly

rotate the flange bolt (31) in clockwise direc-

tion. The saw shaft lock (4) engages after no

Anl_4300685.indb 50Anl_4300685.indb 50 08.10.12 17:2308.10.12 17:23

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PKS 1700 B2 - IAN 79729 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PKS 1700 B2 - IAN 79729

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info