Bedienungsanleitung Parkside POF 1200 A1 - IAN 100129 (Seite 7 von 55) (Deutsch, Englisch, Holländisch, Schwedisch, Finnisch)

576627

Zoom out

Zoom in

Vorherige Seite

1/55

Nächste Seite

7 GB

Introduction / General power tool safety warningsIntroduction

1 Socket head wrench

1 Set of operating instructions

Technical Data

Rated power input: 1200 W

Rated voltage: 230 V∼, 50 Hz

Idle speed: n

11000–30000 min

-1

Plunge depth: 55 mm

Tool holder: 6/8 mm

Protection class: II /

Noise and vibration data:

Measured sound value determined according to

EN 60745. The A-rated noise levels of the electrical

power tool are typically at:

Sound pressure level: 84.7 dB(A)

Sound power level: 95.7 dB(A)

Uncertainty K: 3 dB

Wear hearing protection!

Evaluated acceleration, typically:

Hand / arm vibration a

= 6.437 m / s²

Instability K = 1.5 m / s²

The vibration level speciﬁed in

these instructions was measured in accordance with

an EN 60745 standardised measurement process

and can be used to compare equipment. The vibra-

tion emission value speciﬁed can also serve as a

preliminary assessment of the exposure.

The vibration level will change according to the ap-

plication of the electrical tool an in some cases may

exceed the value speciﬁed in these instructions. Re-

gularly using the electric tool in such a way may

make it easy to underestimate the vibration.

Note: If you wish to make an accurate assessment

of the vibration loads experienced during a particu-

lar period of working, you should also take into

account the intervening periods of time when the

device is switched oﬀ or is running but is not actual-

ly in use. This can result in a much lower vibration

load over the whole of the period of working.

General power tool

safety warnings

Read all safety

warnings and all instructions.

Failure to follow the warnings and in-

structions may result in electric shock, ﬁre and / or

serious injury.

Save all warnings and instructions for

future reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-op-

erated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) D

o not operate power tools in explosive

atmospheres, such as in the presence

of flammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distractio

can cause you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodiﬁed plug

and matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or

wet conditions. Water entering a power tool

will increase the risk of electric shock.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside POF 1200 A1 - IAN 100129 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info