779475
28
Zoom out
Zoom in
Vorherige Seite
1/115
Nächste Seite
PSBSAP 20-Li A1
24 GBIE
Inserting/removing the battery pack
Inserting the battery pack
Set the rotation direction switch to the middle
position (lock). Push the battery pack! into
the handle until it clicks into place.
Removing the battery pack
Press the release button. and remove the
battery pack!.
Checking the battery charge level
Press the battery charge level button1 to
check the status of the battery (see the main
diagram). The status/remaining charge will be
shown on the battery display LED6 as follows:
RED/ORANGE/GREEN = maximum charge
RED/ORANGE = medium charge
RED = low charge – charge the battery
Additional handle
NOTE
For safety reasons, you should never use
this tool without the additional handle
attached.
Loosen the strap on the additional handle
by turning it clockwise.
Slide the mounting ring for the additional
handle over the chuck3.
Turn the additional handle to the required
position.
Afterwards, twist the additional handle
anticlockwise again to tighten it.
Depth stop
Push the locking button for the depth stop
and keep it pushed in.
Fit the depth stop into the additional
handle.
Make sure that the teeth on the depth stop
point upwards and downwards.
Pull the depth stop out until the distance
between the tip of the drill and the tip of the
depth stop corresponds with the required
drilling depth.
Release the locking button for the depth stop
to lock the depth stop in place.
Changing tools
Your cordless impact drill driver has a fully auto-
matic spindle lock .
When the motor is stopped, the power train is
locked so that the chuck3 can be opened by
turning . After you have attached the desired
tool and tightened it by turning the chuck , you
can continue working. The spindle lock is released
automatically when the motor is started (by pressing
the ON/OFF switch).
Torque selection/selecting the
operating mode
You can set the torque using the torque selection
ring- or by choosing between the drill setting
and the hammer drill setting .
Select a low level for small screws or soft
materials.
Select a high level for large screws, hard
materials or removing screws.
Select the drill setting for drilling work by adjusting
the torque selection ring to the position .
Select the hammer drill setting for hammer drilling
work by adjusting the torque selection ring to
the position .
IB_329699_PSBSAP20-LiA1_LB8.indb 24 26.08.20 13:41
28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PSBSAP 20-Li A1 - IAN 329699 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info