779475
29
Zoom out
Zoom in
Vorherige Seite
1/115
Nächste Seite
PSBSAP 20-Li A1 GBIE │25
2-speed gearbox
CAUTION!
Operate the speed selector switch only
when the tool is at a standstill. Otherwise,
the tool could be damaged.
In first gear
(speed selector switchin position 1),
you can reach a speed of approx. 400 rpm and a
high torque. This setting is suitable for all screwing
work.
In second gear
(speed selector switchin position 2),
you can reach a speed of approx. 2000 rpm for
carrying out drilling work.
Operation
Switching on/off
Turn on
Press and hold the ON/OFF switch to start
the tool. The LED work light lights up when
the ON/OFF switch is pressed lightly or
fully. This provides illumination of the work
area in poor lighting conditions.
Switching off
Release the ON/OFF switch to switch off
the tool.
Setting the rotational speed
Pressing the ON/OFF switch lightly yields a low
speed. Increasing the pressure increases the speed.
NOTE
The integrated motor brake ensures that the
tool stops quickly.
Changing the direction of rotation
Change the direction of rotation by pushing the
rotation direction switch to the right or left.
Tips and tricks
Tip! How to do things correctly.
Before operation, check whether the screw
or drill bit is correctly fitted, i.e. centred in the
chuck.
Screw bits are labelled according to their di-
mensions and their shape. If you are uncertain,
always check first whether the bit fits tightly in
the screw head without any play.
Torque
Smaller screws/bits can be damaged if you
set too high a torque or too high a speed.
Hard screw joints (in metal)
Particularly high torques occur, e.g. in metal
screw joints when using drive sockets. Select
a low rotational speed.
Soft screw joints (e.g. in soft wood)
Here, too, use a low speed to avoid damaging
the wood surface when it comes into contact
with the metal screw head. Use a countersink.
Small screws can be screwed directly into soft
wood without predrilling.
When drilling in wood, metal and other
materials, observe the following:
Use a high speed for drill bits with a small
diameter and a low speed for drill bits with
a large diameter.
Select a low speed for hard materials and
a high speed for soft materials.
Mark the spot where you want to drill using
a centre punch or nail. Select a low rotational
speed when starting.
Pull the rotating drill bit from the hole repeatedly
to remove dust and chips and clear the hole.
IB_329699_PSBSAP20-LiA1_LB8.indb 25 26.08.20 13:41
29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PSBSAP 20-Li A1 - IAN 329699 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info