Bedienungsanleitung Parkside PSR 310 A1 - IAN 271263 (Seite 46 von 51) (Französisch, Italienisch)

679212

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

46 GB

When working on wood, and especially when

working on materials which could produce

harmful dust, connect the device to a suitable

external dust extraction.

Ensure adequate ventilation when working on

plastics, paint, lacquer, etc.

The sanding brush is designed for dry grinding

areas on wood, plastic, metal and spackle, as

well as painted surfaces. Only use the device

for dry grinding.

Do not work on materials containing asbestos.

Asbestos is considered carcinogenic.

TOXIC DUST! Dust from

materials such as lead paint, some types of

wood, minerals and metal, can be noxious.

Touching or inhaling this type of dust can pre-

sent a danger to the user or persons nearby.

Wear safety glasses and

a dust mask!

Secure the work piece. Use clamps or a vice to

secure the work piece. This is much safer than

holding it in your hand.

Never place your hands next to or in front of

the device and the surface you are working on,

as slipping poses a risk of injury.

In the event of danger, immediately pull the mains

plug out of the socket.

Always run the mains cable away from the

appliance and toward the rear.

Avoid contact with the sanding sleeve in motion.

Do not work on moistened materials or damp

surfaces.

Always apply the device to the working surface

when switched on. When the task is complete,

lift the appliance oﬀ the work piece before

switching it oﬀ.

Always ﬁrmly hold the device with both hands

whilst working. Ensure you have a solid stance.

Allow the device to come to a complete stop

and switch oﬀ before putting it down.

Always unplug from the mains socket before

taking breaks, especially working on the de-

vice (e.g. replacing sandpaper) and during

non-use.

Start-up

RISK OF INJURY! Always

unplug from the mains before working on the sand-

ing brush.

Installing / replacing grinding

tools (see Fig. A–C)

Activate the spindle lock

(until it locks in)

and use the hexagonal key

to loosen the

clamping screw

Now remove the clamping screw.

Now remove the grinding tool.

Install the respective grinding tool accordingly,

in reverse order.

Activate the spindle lock

(until it locks in)

and use the hexagonal key

to tighten the

clamping screw

Attach the slatted grinding discs

directly onto

the grinding spindle

First mount the shank

into spindle

, then

insert the sanding sleeves

onto the shank.

Installing sanding sleeves

(see Fig. D)

Follow the direction of slats and turn the sand-

ing sleeve

over the mounting shank

until

the rubber slats are completely covered.

Removing the sanding sleeves

Be sure the mounting shank

remains inside

the spindle

during removal.

To replace or remove an old sanding sleeve

ﬁrst activate the spindle lock

until it locks in.

Then using a rotating motion following the direc-

tion of the slats on the mounting shank

to pull

oﬀ the sanding sleeve

General power tool safety warnings / Start-up Start-up / Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PSR 310 A1 - IAN 271263 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PSR 310 A1 - IAN 271263

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info