Bedienungsanleitung Parkside PSR 310 A1 - IAN 271263 (Seite 47 von 51) (Französisch, Italienisch)

679212

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

47 GB

General power tool safety warnings / Start-up

Installing the dust extraction

hood (see Fig. E)

Insert the dust extraction hood

into the two

fastening grooves

on the tool arm

against

slight resistance.

Tighten the clamping screw

. The dust ex-

traction hood

is now ﬁrmly installed on the

tool arm

Adjusting the dust extraction

hood (see Fig. F)

Adjust the dust extraction hood

so dust or

sparks are not directed at the user.

The dust extraction hood

can cover the

grinding spindle from various angles. Use the

locking grooves

for this purpose.

Following installation, rotate the dust extraction

hood

toward the handle

according to

the application and the work piece. The dust

extraction hood

will lock into place in sev-

eral positions.

External extraction

EXPLOSION HAZARD!

A special dust extractor must be used for explosive

dust / air mixtures.

FIRE HAZARD DUE TO SPARKING! Do not

use dust extraction when working on metal.

FIRE HAZARD! Using power

tools which can be connected to a vacuum using a

dust extraction poses a ﬁre hazard! Unfavourable

conditions, e.g. sparking - when grinding metal or

metal pieces in wood - can ignite wood dust inside

the vacuum bag. This can particularly occur if the

wood dust is mixed with paint particles or other

chemicals and the ground product is hot after long

work periods. Therefore be sure to avoid the ground

materials and the device from overheating and al-

ways empty the vacuum bag before taking breaks.

Wear a dust mask!

Connecting the dust extraction hose

Slide the vacuum adapter

into the connecting

piece

(see Fig. G).

Slide the hose from a reliable dust extraction

(e.g. a workshop vacuum) into the vacuum

adapter

Removing the dust extractor hose

Pull the hose out of the dust extraction unit.

Operation

RISK OF INJURY! Always

unplug from the mains before working on the sand-

ing brush.

Firmly hold the power tool with both hands whilst

working and ensure a solid stance. Holding the

power tool with both hands is safer.

Note the mains voltage! The voltage of the pow-

er source must correspond with the speciﬁca

tions

on the type plate of the power tool.

Switching on / oﬀ

To switch on the power tool, slide the on / oﬀ

switch

forward so the switch shows “1“.

To save power, only switch on the power tool

when in use.

To switch oﬀ the power tool, slide the on / oﬀ

switch

back so the switch shows “0“.

Check the grinding tool before use.

The grinding tool must be properly installed

and rotate freely. Perform a test run of at least

1 minute without load. Do not use damaged,

untrue vibrating grinding tools. Damaged

grinding tools could burst and cause injuries.

Selecting the grinding tool

Select the grinding tool according to the shape of

surface to be worked on and the material to be sand-

ed. Match the grit with the desired material removal.

Start-up / Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PSR 310 A1 - IAN 271263 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PSR 310 A1 - IAN 271263

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info