Bedienungsanleitung Parkside PSS 250 A1 - IAN 104446 (Seite 10 von 50) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

595334

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

10 GB/IE

Operation / Maintenance and Cleaning / Service centre / WarrantyOperation

Sanding sheets without hook and loop

fastening:

Open the two clamping levers

Push one end of the sanding sheet

under the

open clamping bar

and clamp the sheet ﬁrmly

in place by locking the clamping lever

back

in place.

Repeat this procedure at the other end.

Various materials require diﬀerent grit values. You

can read which grit value is best suited for which

work in our recommendations under “Instructions,

tips and tricks”.

Vacuuming dust

FIRE HAZARD! A risk of ﬁre

exists when working with electrical appliances that

have a dust collection box

or can be attached to

a vacuum cleaner via an external suction adapter!

Under certain conditions the sanding dust in the dust

box (or in the vacuum’s dust bag) may self-ignite, e.g.

as a result of ﬂying sparks generated when abrading

metals or metal objects left in wood. This can happen

especially if the wood dust has paint particles on it

or is mixed with other chemical substances and the

sanded material is hot after extensive working. You

should therefore avoid overheating of products be-

ing sanded as well as the appliance and always

empty the dust collection box

or the dust bag of

the vacuum cleaner before work pauses.

Wear a dust mask!

Vacuuming dust with the dust

collection box

Attach the dust collection box:

Push the dust collection box

on to the device.

Remove the dust collection box:

Press the release button(s)

and pull the dust

collection box

oﬀ the device.

NOTE: Always empty the dust collection box

in due time and shake any remaining dust out; this

will ensure optimal vacuum performance.

Dust extraction using an external

vacuum extraction device

Connecting:

For vacuum dust removal using a vacuum

cleaner, push the suction hose of a vacuum

cleaner approved for use as a dust extraction

device (e.g. a workshop vacuum cleaner) into

the connection

– see Fig. D.

NOTE: If it is necessary to use the reducer piece

, push the reducer piece into the connection

Removing:

Pull the hose of the dust extraction device oﬀ

the connection

or oﬀ the reducer piece

if one is used.

Instructions, tips and tricks

Move the oscillating sander parallel, in ﬂat

circles or alternating between lengthwise and

side-to-side motions.

Do not press down with the oscillating sander.

The sanding sheets become clogged, which

reduces the sanding performance.

Clean the sanding sheet

occasionally with

the vacuum cleaner.

The removal performance and therefore the re-

sult of your work are determined by the correct

selection of the speed and sanding sheet

grit.

Never sand diﬀerent materials with the same

sanding sheet

(e.g. wood then metal).

The following table oﬀers some values, which are

for information only and may simplify the selection

of a sanding sheet

Wood Sanding sheet / Grit

Sanding of wood 40–240

Pre-sanding, e.g. of

rough, unplaned

beams and boards

40, 60

Surface sanding 80, 100, 120

Fine sanding of hard

woods

180, 240

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PSS 250 A1 - IAN 104446 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info