Bedienungsanleitung Parkside PTHSA 20-Li B3 - IAN 405768 (Seite 15 von 216) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch)

819958

Zoom out

Zoom in

Vorherige Seite

1/216

Nächste Seite

PTHSA 20-Li B3

■ 10 │ GB│IE

Checking the battery charge level

♦ Press the battery charge level buttoni to

check the status of the battery (see also main

diagram). The status will be shown on the

battery display LEDu as follows:

RED/ORANGE/GREEN = maximum charge

RED/ORANGE = medium charge

RED = low charge – charge the battery

Inserting/removing the battery pack

Inserting the battery pack

♦ Push the battery packr into the handle until it

clicks into place.

Removing the battery pack

♦ Press the release buttont and remove the

battery packr.

WARNING! RISK OF INJURY!

► Before any work on the appliance, remove

the battery. Risk of electric shock!

Fixing/attaching the shoulder strap

♦ Hook the shoulder strape into the carrying

lug9.

♦ Adjust the length of the shoulder strape to

your size so that the carrying lug9 is at hip

height when the strap is hooked in place.

Mounting the motor head on the

telescopic handle

♦ Undo the quick release7 by pressing it in

the direction of the arrow . Pull out the

telescopic handle until the black plastic ring

is exposed.

♦ Place the lower end of the motor head3 on

the upper end of the telescopic handle6 so

that the motor head3 can be pushed through

as far as the black plastic ring. Make sure that

the groove and the recess interlock with each

other.

♦ Tighten the red connecting piece5 by turning

it towards the symbol on the motor head3.

Adjusting the telescopic handle

The telescopic handle6 can be adjusted continu-

ously by means of the quick release7.

♦ Undo the quick release7 by pressing it in the

direction of the arrow and adjust the

length by pushing or pulling as required.

♦ Close the quick release again7 to ﬁx the

desired working length of the telescopic

handle6.

♦ If the screws on the quick-release7 have loos-

ened, tighten them again with the hex keyw.

Adjusting the cutting angle

NOTE

► The cutting angle can be adjusted in 11 stages.

♦ Remove the battery packr from the appliance.

♦ Press the release button4.

♦ Adjust the angle of the motor unit to the

required position.

♦ Let go of the release button4 and the motor

unit will click into place.

♦ Insert the battery packr back into the appli-

ance.

Use

NOTE

► Comply with regulations regarding noise

protection and local rules. Using the appli-

ance on certain days (e.g. on Sundays and

public holidays), during certain times

(midday, night time) or in certain locations

(e.g. health resorts, clinics, etc.) may be

restricted or prohibited.

Switching on/oﬀ

Turn on

♦ Press the safety lock-out0 and keep it pressed

and then press the On/Oﬀ switchq. You can

now release the safety lock-out0.

Switching oﬀ

♦ Release the On/Oﬀ switchq.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PTHSA 20-Li B3 - IAN 405768 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info